Single engine belt r r

Operation 1092G10 · Single drive belt for various engine components

1.6 TS

Removing

Position the vehicle on the ramp.

Proceed with the removal - 4450B10 Front WHEEL (one) - R.R. (Right side).

Proceed with the removal - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side).

1. Use a spanner on the moving tensioner (1a) and remove the single drive belt (1b).

Refitting

Use a spanner on the moving tensioner and fit the engine components single drive belt.

Proceed with the refitting - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side).

Proceed with the refitting - 4450B10 Front WHEEL (one) - R.R. (Right side).

Remove the car from the ramp.

2.0 TS

Removing

Position the vehicle on the ramp.

Proceed with the removal - 4450B10 Front WHEEL (one) - R.R. (Right side).

Proceed with the removal - 7055B54 under-engine guard - r r.

Proceed with the removal - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side).

1. Undo the bolts (1a) and the nut (1b) and remove the engine components single drive belt guard (1c).

1. Use a spanner on the moving tensioner (1a) and remove the single drive belt (1b).

Refitting

Use a spanner on the moving tensioner and fit the engine components single drive belt.

Place the engine components single drive belt guard back in its housing and secure it using the bolts and the nut.

Proceed with the refitting - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side).

Proceed with the refitting - 7055B54 under-engine guard - r r.

Proceed with the refitting - 4450B10 Front WHEEL (one) - R.R. (Right side).

Remove the car from the ramp.

3.2 V6

Removing

Position the vehicle on the ramp.

Proceed with removal - 4450B04 right front wheel r r.

Proceed with removal - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R..

1. Loosen the engine components single drive belt tension adjusting the moving tensioner using a spanner.

2. Lock the moving tensioner (2a) with the belt slack inserting a suitable peg (2b).

3. Remove the engine components single drive belt.

Refitting

Place the engine components single drive belt in its housing.

Use a spanner on the moving tensioner to extract the peg.

Proceed with refitting - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R..

Proceed with refitting - 4450B04 right front wheel r r.

Remove the car from the ramps.

1.9 JTD 8V

Removing

Place the car on a ramp.

- 7055B54 under-engine guard - r r

- 4450B04 right front wheel r r

- 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R.

1. Act on the moving tensioner to loosen the tension of the engine components single drive belt.

2. Remove the auxiliary shaft drive belt.

Refitting

Fit a new single drive belt on the pullies.

Do not allow oil or solvents to come into contact with the belt, as these could affect the flexibility of the rubber, resulting in reduced grip. Also check that there are no cracks or cuts on the belt, otherwise it will have to be replaced.

The tensioning device is automatic: a preloaded spring adjusts the belt to the correct tension upon installation and automatically takes up any slack in the belt generated during normal operation.

Act on the automatic tensioning device and place it in the maximum pre-loading position, fit the auxiliary shaft drive belt and slowly release the tensioning device.

- 4450B04 right front wheel r r

- 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R.

- 7055B54 under-engine guard - r r

Remove the vehicle from the ramp.

1.9 JTD 16V

Removing

Position the vehicle on the ramp.

Proceed with removal - 4450B04 right front wheel r r.

Proceed with removal - 7055B54 under-engine guard - r r.

Proceed with removal - 7055B91 Right front WHEEL ARCH LINER - R.R..

1. Use a spanner on the moving tensioner (1a) and remove the single drive belt (1b).

Refitting

Adjust the moving tensioner and fit the engine components single drive belt using a spanner.

Proceed with refitting - 7055B91 Right front WHEEL ARCH LINER - R.R..

Proceed with refitting - 7055B54 under-engine guard - r r.

Proceed with refitting - 4450B04 right front wheel r r.

Remove the car from the ramps.