Workshop Manuals Factory service & repair Fiat
01 General information02 Specifications03 Manufacturing data and tolerances04 Tightening torques05 Fluids and lubricants06 Maintenance07 Diagnostic checks08 Engine09 Clutch10 Gearbox and differential11 Axles and driveshafts12 Brakes13 Steering14 Suspension and wheels15 Heating, air conditioning and auxiliary units16 Electrical equipment17 Body fittings18 Body panels and frame19 Wiring diagrams and electrical functions20 Wiring harnesses21 Connectors and pin-outs22 Fault diagnosis23 Special tools
Fiat Grande Punto Factory Service Manual (2005-2012)13 · Steering
13 · Steering & suspension

Steering electrical control device - r r

Make
Fiat
Model
Grande Punto Factory Service Manual
Year
2005–2012
Section
Steering control and linkage › Steering electrical control device - r r
SteeringSteering electrical control device - r r

STEERING ELECTRICAL CONTROL DEVICE - R R

Operation 4110D20 · STEERING ELECTRICAL CONTROL SYSTEM

Removing

- Place the front wheels straight, then engage the first steering lock to the right and remove the ignition key.

- Keep the steering column adjustment lever closed during all the removing-refitting stages.

- Do not, under any circumstances, remove the upper shaft during the removal of the steering column from its housing.

Op. 5580C18 AIR BAG MODULE - R+R

Op. 4110A10 STEERING WHEEL - R+R FOR REPLACEMENT OR CHECKS

Op. 5550A10 STALK UNIT ASSEMBLY - R+R

Op. 7040A30 LEFT LOWER DASHBOARD TRIM - R.R.

Op. 5010C55 LOWER AIR DIFFUSER (ONE) LH OR RH - R.R

(left side).

Op. 5580E08 AERIAL FOR ELECTRONIC KEY (CODE) - R.R

- Cover the centre of the dashboard with suitable protection to avoid damage during the final stage of removing the steering column.

1. Undo the bolt (1a) fixing the steering column to the steering box pinion (1b).

STEERING ELECTRICAL CONTROL DEVICE - R R

1. Disconnect the electrical connections (1a) and (1b) from the electric steering control unit.

DescriptionConnector
1aElectric steering control unitSee M086 ELECTRIC STEERING CONTROL UNIT
DescriptionConnector
1bElectric steering control unitSee M086 ELECTRIC STEERING CONTROL UNIT

2. Undo the nuts (2a) and the bolts (2b) fixing the steering column to the crossmember under the dashboard.

STEERING ELECTRICAL CONTROL DEVICE - R R

1. Grip the steering column (1a) as illustrated and remove it from its housing releasing it firstly from the two studs (1b) and then from the dashboard frame bracket (1c).

To facilitate the final removal stage, turn the steering column towards the centre of the dashboard protected previously against any impacts.

STEERING ELECTRICAL CONTROL DEVICE - R R

If the steering column is being reused, do not, under any circumstances, release the upper shaft.

Therefore bind the moving parts as illustrated in the diagram.

STEERING ELECTRICAL CONTROL DEVICE - R R

Refitting

- Place the steering column in position and secure it tightening the nuts and the bolts to the recommended torque.

ComponentFasteningdiaValue (daNm)Validity
Steering column to underdashboard crossmemberNutM81.6 ÷ 2.4
ComponentFasteningdiaValue (daNm)Validity
Steering column to underdashboard crossmemberBoltM81.6 ÷ 2.4

- Remove the binding from the steering column moving parts.

- Connect the electrical connections for the electric steering control unit.

- Connect the steering column to the steering box pinion and secure by tightening the bolt to the specified torque.

ComponentFasteningdiaValue (daNm)Validity
Steering column to steering box pinionBoltM105.0 ÷ 6.0

- Remove the protection used for covering the centre area of the dashboard.

Op. 5580E08 AERIAL FOR ELECTRONIC KEY (CODE) - R.R

Op. 5010C55 LOWER AIR DIFFUSER (ONE) LH OR RH - R.R

(left side).

Op. 7040A30 LEFT LOWER DASHBOARD TRIM - R.R.

Op. 5550A10 STALK UNIT ASSEMBLY - R+R

Op. 4110A10 STEERING WHEEL - R+R FOR REPLACEMENT OR CHECKS

Op. 5580C18 AIR BAG MODULE - R+R

Parts & tools for this job For 2005 Fiat Grande Punto

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.