Abbreviations and symbols used in this manual
- Make
- Land Rover
- Model
- Defender V8i Workshop Manual Supplement
- Section
- Information › Abbreviations and symbols used in this manual
IntroductionAbbreviations and symbols used in this manual
ABBREVIATIONS AND SYMBOLS USED IN THIS MANUAL
| Across flats (bolt size) | AF Litres ..................................................................... |
| After bottom dead centre | ABDC Low tension ............................................................. |
| After top dead centre | ATDC Maximum ............................................................ |
| Alternating current | a.c. Metre ........................................................................ |
| Ampere | amp Millilitre .................................................................... |
| Ampere hour | amp hr Millimetre ............................................................... |
| Before bottom dead centre | BBDC Miles per gallon .................................................... |
| Before top dead centre | BTDC Miles per hour ...................................................... |
| Bottom dead centre | BDC Minute (angle) ............................................................ |
| Brake horse power | bhp Minus (of tolerance) ................................................... |
| British Standards | BS Negative (electrical) ................................................... |
| Carbon monoxide | CO Newton metres (torque) ........................................ |
| Centimetre | cm Number ................................................................. |
| Centigrade (Celsius) | C3 Ohms ................................................................... |
| Cubic centimetre | cm3 Ounces (force) ....................................................... |
| Cubic inch | in Ounces (mass) ........................................................ |
| Degree (angle) | deg or ° Outside diameter ................................................. |
| Degree (temperature) | deg or ° Part number ................................................... |
| Diameter | dia. Percentage ............................................................... |
| Direct current | d.c. Pints ......................................................................... |
| Electronic Control Unit | ECU Plus (tolerance) ......................................................... |
| Electronic Fuel Injection | EFI Positive (electrical) .................................................... |
| Fahrenheit | F Pound (force) .......................................................... |
| Feet | ft Pounds inch (torque) ........................................... |
| Feet per minute | ft/min Pound (mass) ........................................................... |
| Fifth | 5th Pounds per square inch ..................................... |
| First | 1st Ratio ........................................................................... |
| Fluid ounce | fl oz Reference .............................................................. |
| Foot pounds (torque) | lbf.ft Revolution per minute ..................................... |
| Fourth | 4th Right-hand ............................................................. |
| Gramme (force) | gf Second (angle) ........................................................... |
| Gramme (mass) | g Second (numerical order) ...................................... |
| Gallons | gal Specific gravity ................................................... |
| High tension (electrical) | H.T. Square centimetres ............................................... |
| Internal diameter | I.D. Square inches ......................................................... |
| Inches of mercury | in. Hg Standard wire gauge ......................................... |
| Inches | in Synchroniser/Synchromesh .......................... |
| Kilogramme (force) | kgf Third ....................................................................... |
| Kilogramme (mass.) | kg Top dead centre .................................................. |
| Kilogramme centimetre (torque) | kgf.cm2 United Kingdom ...................................................... |
| Kilogramme per square millimetre | kgf/mm2 Vehicle Identification Number ............................... |
| Kilogramme per square centimetre | kgf/cm Volts ......................................................................... |
| Kilogramme metres (torque) | kgf.m Watts ....................................................................... |
| Kilometres | km |
| Kilometres per hour | km/h SCREW THREADS |
| Kilovolts | kV American Standard Taper Pipe ......................... |
| Left-hand | LH British Standard Pipe ........................................... |
| Left-hand steering | LHStg Unified Coarse .................................................... |
| Left-hand thread | LHThd Unified Fine ......................................................... |
litre l.t. max. m ml mm mpg mph ’ - - Nm No. ohm ozf oz O.D. Part No. % pt + + lbf lbf.in lb P.S.I. : ref. rev/min RH " 2nd sp.gr.2 cm2 in s.w.g. synchro. 3rd TDC UK VIN V W
NPTF BSP UNC UNF
Parts & tools for this job For Land Rover Defender
- TOOLTorque wrenchSearch: 3/8 inch torque wrench
- TOOLSocket setSearch: socket set metric
- BOOKHaynes manualSearch: Haynes manual Land Rover Defender
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.