Workshop Manuals Factory service & repair Nissan and Datsun
01 Nissan-S110 S12 S13 S14 S15 Silvia 200SX 240SX02 INDEX03 GI - General Information04 MA - Maintenance05 EM - Engine Mechanical06 LC - Engine Lubrication & Cooling07 EF&EC - Fuel & Emission Control08 FE - Engine Control, Fuel & Exaust09 CL - Clutch10 MT - Manual Transmission11 AT - Automatic Transmission12 PD - Propeller Shaft & Differential13 FA - Front Axle & Suspension14 RA - Rear Axle & Suspension15 BR - Brake System16 ST - Steering System17 BF - Body18 HA - Heater & Air Conditioner19 EL - Electrical System20 Inch/Metric Converion Tables21 Quick Reference Chart
Nissan and Datsun Nissan 200SX S12 1986 Workshop Manual07 · EF&EC - Fuel & Emission Control
07 · Engine

DIAGNOSTIC PROCEDURE - Nissan 200SX S12 Workshop Manual

Make
Nissan and Datsun
Model
200SX Nissan 200SX S12 1986 Workshop Manual
Section
General › DIAGNOSTIC PROCEDURE - Nissan 200SX S12 Workshop Manual
EF&EC - Fuel & Emission ControlDIAGNOSTIC PROCEDURE - Nissan 200SX S12 Workshop Manual

DIAGNOSTIC PROCEDURE

DIAGNOSTIC PROCEDURE

Driveability {Cont’d). 4, Inspect engine and E.F.I./E.C.C.S, for air leaks, CATsET proper electrical connections, etc, J} Check al! hoses end ducts for air leaks. 2) Check air clesner for clogging. 3) Check harness connectors for proper connec: tions, 4). Check ignition wiring. 5 Check gaskets for leaks at all air intake com- ponents, . ‘6} Check sir regulator operation, 1) Check E.G.R. valve operation. serovre wareass 3, Perform £.F.1,/E.C.C.S. self-diagnosis, |

Follow the procedure in E.F.i,/E.C.C.S, SELF-

}

DIAGNOSIS (Pages EF & EC-41 - 48),

3. Check idle speed and ignition timing. 3) Check ignition timing with a timing light, ‘4. Prepere the following conditions: «Battery is in good order.

Headlamp switch: OFF

by Hoater blower: OFF TALDa 20° 8.7.0.6. twnits)

meg Air conditioner switch: OFF 4 fae e2e8e) \ Front wheel (Power steering model) :

bend (ae =" TOL.

KEEP STRAIGHT AHEAD

Warm angina to operating temperatura, Check and adjust as follows: oMaiaoa ) Rece engine two or three times under no-load, then run engine at idle speed. CA20E (Without vacuum advance) : Check idle speed. M/T 4:2" B.T.0.C, 032° B.T.0.c, AIT wpasd: rpm

CAIBET: 15+2° B.T.D.C.

AIT (in “D” position) If necessary, adjust ignition timing by turning distributor. 7002700 4) Check throttle valve switch (Idle contact}, and adjust if necessary. (Refer to page EF & £C-23.) OFF + ON:

f f necessary, adjust to the specified speed by

M/T Idle speed +150*60 rpm A/T — Engine speed (in “N” position) turning the idle speed adjusting screw. +180450 rpm

4. Perform driveability test. Evaluate effectiveness of adjustments by driving vehicle. If unsatisfactory, proceed to step 6.

EF & EC-37

Parts & tools for this job For Nissan 200SX

As an Amazon Associate we earn from qualifying purchases.