Workshop Manuals Factory service & repair SEAT
01 Power transmission02 Running gear03 Body04 Power tramsmission05 Power unit06 Vehicle electrics07 Heating-ventilation-air conditioning system08 Automatic gearbox09 Engine, mixture preparation10 Engine, mechanics11 Manual gearbox12 Running gear - self diagnosis13 Heating and air conditioning14 Bodywork15 Heating, ventilation, air conditioning system
SEAT Leon Mk201 · Power transmission
01 · Transmission

Adjusting differential

Make
SEAT
Model
Leon Mk2
Section
Final drive, differential, differential lock › Differential › Adjusting differential
Power transmissionAdjusting differential
   
Adjusting differential
Diagram not available
Special tools and workshop equipment required
t  Thrust plate -VW 401-
t  Thrust plate -VW 402-
t  Press tool -VW 408 A-
t  Press tool -VW 412-
t  Thrust piece -VW 442-
t  Removal and installing tool -VW 459/1-

   
Diagram not available
t  End dimension plate -VW 385/17-
t  Universal dial gauge bracket -VW 387-
t  Thrust plate -40-105-
t  Thrust piece -2050-
t  Tube -3259-
t  Tube -3345-

   
t  Torque wrench -V.A.G 1331-
  Diagram not available
t  Three arm puller -Kukko 45-2-
It is necessary to readjust the differential when
t  Gearbox housing
t  Clutch housing
t  Differential cage
or the
t  Tapered roller bearings of differential
have been renewed.
Adjustment overview → Chapter.
  Diagram not available
–  Press tapered roller bearing outer race with shim into clutch housing → Fig..
  Diagram not available
–  Press tapered roller bearing inner race without shim into gearbox housing.
–  Fit differential into clutch housing.
–  Fit gearbox housing and tighten 5 bolts to specified torque → Item and → Item.
–  Press differential in direction of clutch housing while turning it eight times.
Adjusting differential – SEAT Leon Mk2  Note!
t  Now turn gearbox with clutch housing upwards in assembly stand.
t  This is absolutely necessary for performing correct measurements.
–  Press differential in direction of gearbox housing while turning it eight times.
  Diagram not available
–  Secure universal dial gauge bracket -VW 387- to clutch housing and set dial gauge to “0” with 1 mm preload.
–  Move differential up and down. Read and note play indicated on dial gauge. (Example: 0.70 mm)
Determining thickness of shim
The specified bearing preload is obtained by adding a constant value for preload (0.30 mm) to the reading obtained.
Example:
  Diagram not available
 Measured value0.70 mm
+Preload (constant value)0.30 mm
 Thickness of shim =1.00 mm

–  Remove gearbox housing.
   
–  Pull tapered roller bearing inner race off gearbox housing.
A - Three arm puller, e.g. -Kukko 45-2-
–  Determine thickness of shim from table.
–  Determine part number of shim according to → Electronic parts catalogue (ETKA).
–  Insert shims of determined thickness with thickest shim first.
The following shims are available:
  Diagram not available
Shim thickness (mm)
0.650.851.051.25
0.700.901.101.30
0.750.951.151.35
0.801.001.201.40

If the size of shim required is larger than those listed in the table, insert two shims totalling the correct figure.
The various thicknesses make it possible to achieve the exact shim thickness required.
   
–  Press tapered roller bearing inner race in again and tighten gearbox housing to specified torque → Item and → Item.
  Diagram not available

The same page in: Leon Mk1, Leon Mk2.

Parts & tools for this job For SEAT Leon

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.