Octavia Mk2
Note
| 1 - | Gearbox housing |
| 2 - | Adjusting washer |
| q | for differential gear |
| q | Determine thickness → Chapter |
| 3 - | Outer ring/tapered-roller bearing |
| q | removing → Fig. |
| q | installing → Fig. |
| 4 - | Inner ring/tapered-roller bearing |
| q | remove → Fig. |
| q | pressing on → Fig. |
| 5 - | Differential gear housing |
| q | with gear pinion for final drive |
| q | Differential gear housing adapted to stop disc compound |
| q | The hole of the tensioning sleeve is adapted to the length of the tensioning sleeve → Fig. |
| q | assign according to the → Electronic catalogue of original parts. |
| 6 - | Inner ring/tapered-roller bearing |
| q | remove → Fig. |
| q | pressing on → Fig. |
| 7 - | Outer ring/tapered-roller bearing |
| q | pressing out → Fig. |
| q | installing → Fig. |
| 8 - | Clutch housing |
| 9 - | Sealing ring |
| q | between angle and manual gearbox |
| q | replace → Chapter |
| 10 - | Seal ring for right flange shaft |
| q | replace → Chapter |
| 11 - | 40 Nm and torque a further 45° |
| q | 4 pieces |
| q | always replace → Electronic Catalogue of Original Parts |
| 12 - | 25 Nm |
| q | screw 21 into threaded piece Pos. 21 |
| 13 - | Right flange shaft |
| q | removing and installing → Chapter |
| 14 - | Sealing ring |
| q | remove 15 when replacing the needle bearing Pos. 15 |
| 15 - | Needle bearing |
| q | replace → Chapter |
| 16 - | Circlip |
| q | always replace → Electronic Catalogue of Original Parts |
| 17 - | Angle gearbox |
| q | Removing and installing with manual gearbox fitted → Chapter |
| q | Removing and installing with manual gearbox removed → Chapter |
| 18 - | Sealing ring |
| q | between angle and manual gearbox |
| q | replace → Chapter |
| 19 - | Stop disc compound |
| q | insert with gear oil |
| q | on certain gearboxes the stop disc compound was provided with land → Fig. |
| 20 - | Differential bevel gear, large |
| q | installing → Fig. |
| 21 - | Threaded part |
| q | installing → Fig. |
| 22 - | Differential bevel gear shaft |
| q | drive out with drift |
| q | remove together with short tensioning sleeve → Fig. |
| q | remove together with long tensioning sleeve → Fig. |
| q | installing → Fig. |
| 23 - | Tensioning sleeve |
| q | to secure the axle for differential bevel gears |
| q | Difference between the tensioning sleeves → Fig. |
| q | short tensioning sleeve; removing and installing → Fig. |
| q | long tensioning sleeve; removing → Fig. |
| q | long tensioning sleeve; installing → Fig. |
| 24 - | Differential bevel gear, small |
| q | installing → Fig. |
| 25 - | Circlip |
| q | holds the conical ring, stop disc and pressure spring in position when the flange shaft is removed |
| 26 - | Conical ring |
| q | with slots for thrust washer catch |
| q | Fitting position: Cone towards differential gear housing |
| 27 - | Thrust washer |
| q | Fitting position → Fig. |
| 28 - | Pressure spring for flange shaft |
| q | fitted behind flange shafts |
| 29 - | Flange shaft left |
| q | removing and installing → Chapter |
| 30 - | Seal ring for left flange shaft |
| q | replace → Chapter |
