Workshop Manuals Factory service & repair Fiat
01 General information02 Specifications03 Manufacturing data and tolerances04 Tightening torques05 Fluids and lubricants06 Maintenance07 Diagnostic checks08 Engine09 Clutch10 Gearbox and differential11 Transmission (4x4)12 Axles and driveshafts13 Brakes14 Steering15 Suspension and wheels16 Heating, air conditioning and auxiliary units17 Electrical equipment18 Body fittings19 Body panels and frame20 Wiring diagrams and electrical functions21 Wiring harnesses22 Connectors and pin-outs23 Fault diagnosis24 Special tools
Fiat Ducato Factory Service Manual (2002-2006)13 · Brakes
13 · Brakes

Pump/central obs pipe - r r

Make
Fiat
Model
Ducato Factory Service Manual
Year
2002–2006
Section
Anti-lock brake system – ABS › Pump/central obs pipe - r r
BrakesPump/central obs pipe - r r

PUMP/CENTRAL OBS PIPE - R R

Operation 3340B52 · ABS SYSTEM PIPES

Removing

- Position the vehicle on the lift.

- Remove the protective cap from the bleed valve on the rear brake caliper.

- Connect the recovery device (pipe and reservoir) to the rear brake caliper bleed valve.

- Operate the brake pedal until the brake/clutch reservoir is drained.

Op. 1048A21 FILTER INPUT SLEEVE - R R

Op. 1048A10 AIR CLEANER FILTERING ELEMENT - REPLACE

Op. 7055B54 UNDER-ENGINE GUARD - R R

- Disconnect the negative battery terminal.

1. Disconnect the electrical connection for the ABS control unit.

DescriptionConnector
1ABS control unitM050

2. Undo the connectors for the rigid pipes on the ABS control unit.

PUMP/CENTRAL OBS PIPE - R R

- Release the two rigid pipes from the master cylinder to the ABS hydraulic control unit from the retaining springs.

- Release the two pipes for the additional heater from the spring.

- Lower the lift.

Op. 1040A30 OIL SEAL COVER, FLY WHEEL SIDE - R + R AND REPLACE SEALS

1. Undo the two connectors for the rigid pipes on the brake pump.

PUMP/CENTRAL OBS PIPE - R R

- Release the two rigid pipes from the retaining springs.

1. Remove the rigid pipes from the master cylinder to the ABS hydraulic control unit.

PUMP/CENTRAL OBS PIPE - R R

Refitting

- Check that the intermediate flexible pipe to the rear brakes is not damaged.

- Fit the rigid pipes from the pump master cylinder to the ABS hydraulic control unit.

- Screw in the connectors for the rigid pipes from the master cylinder to the ABS hydraulic control unit without tightening them to torque.

- Attach the rigid pipes to the springs.

- Attach the pipes for the additional heater to the retaining springs.

- Tighten the two connectors for the rigid pipes from the pump master cylinder to the ABS hydraulic control unit.

Value - daNmFasteningComponentØ
(ABS hydraulic control unit ) 1.4ConnectorPIPE FROM PUMP TO HYDRAULIC CONTROL UNITM10
Value - daNmFasteningComponentØ
(ABS hydraulic control unit ) 1.4ConnectorPIPE FROM PUMP TO HYDRAULIC CONTROL UNITM12

- Lower the lift.

- Fasten the connectors for the rigid pipes from the master cylinder to the ABS hydraulic control unit to the master cylinder.

Value - daNmFasteningComponentØ
(Master cylinder) 1.4ConnectorPIPE FROM PUMP TO HYDRAULIC CONTROL UNITM10

- Connect the electrical connection for the ABS control unit.

DescriptionConnector
ABS control unitM050

- Connect the negative battery terminal.

Op. 0010T65 HYDRAULIC BRAKE SYSTEM BLEED AIR

- Remove the vehicle from the lift.

- Test the operation of the braking system.

Parts & tools for this job For 2002 Fiat Ducato

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.