Engine oil supply pipe to turbocharger

Operation 1084B40 · ENGINE OIL LUBRICATION CIRCUIT

2.4 JTD 20V

Removing

- Position the vehicle on a lift.

See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.

See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.

See in Op. 1016A10 SOUND-PROOFING COVER - R.R.

See in Op. 1048B44 RIGID air supply PIPE from heat exchanger to intake manifold - R.R.

See in Op. 1048A56 UPPER RESONATOR - R.R.

See in Op. 1048A50 air inlet pipe to turbocharger - r + r

See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.

See in Op. 1048A10 COMPLETE AIR FILTER -R.R.

1. Undo the fixing nuts (1a) and remove the bonnet lock (1b) from the housing in the crossmember.

2. Undo the lower nut (2a) and remove the lock reinforcement bracket (2b).

1. Undo the retaining bolts.

2. Remove the upper front crossmember.

- Raise the lift.

1. Undo the fitting connecting the engine oil delivery pipe to the turbocharger from the engine block

2. Lower the lift and unscrew the fitting connecting the pipe to the turbocharger.

3. Remove the engine oil delivery pipe to the turbocharger.

Refitting

- Fit the turbocharger engine oil supply pipe to the turbocharger and secure it to the turbocharger using the connector.

- Raise the vehicle.

- Connect the engine oil supply pipe to the engine block and secure it with the connector tightened to torque.

- Lower the vehicle.

- Fit the upper front crossmember and tighten the fixing bolts to torque.

- Fit the bonnet lid lock complete with bracket and tighten the nuts fixing it to the upper crossmember and to the lower crossmember.

See in Op. 1048A10 COMPLETE AIR FILTER -R.R.

See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.

See in Op. 1048A50 air inlet pipe to turbocharger - r + r

See in Op. 1048A56 UPPER RESONATOR - R.R.

See in Op. 1048B44 RIGID air supply PIPE from heat exchanger to intake manifold - R.R.

See in Op. 1016A10 SOUND-PROOFING COVER - R.R.

See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.

See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.

- Remove the vehicle from the lift.

2.0 TB

Removing

See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.

See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.

See in Op. 1048A50 air inlet pipe to turbocharger - r + r

See in Op. 1048A10 COMPLETE AIR FILTER -R.R.

See in Op. 1088E10 Radiator cooling FAN - R.R.

See in Op. 1072C44 Exhaust manifold heat shield on BULKHEAD - R.R.

See in Op. 1016A40 Ignition COIL COVER on cylinder head - R.R.

Refitting

See in Op. 1016A40 Ignition COIL COVER on cylinder head - R.R.

See in Op. 1072C44 Exhaust manifold heat shield on BULKHEAD - R.R.

See in Op. 1088E10 Radiator cooling FAN - R.R.

See in Op. 1048A10 COMPLETE AIR FILTER -R.R.

See in Op. 1048A50 air inlet pipe to turbocharger - r + r

See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.

See in Op. 0010T11 ENGINE OIL - Check level and top up if necessary

See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.

2.4 JTD 10V

Removing

See in Op. 1016A10 SOUND-PROOFING COVER - R.R.

1. Undo the fixing nuts (1a) and remove the bonnet lock (1b) from its housing in the crossmember.

2. Undo the lower unti (2a) and remove the lock reinforcement bracket (2b).

1. Undo the fixing nuts.

2. Remove the upper front crossmember.

1. Remove the cold air intake from the connector on the air filter.

1. Undo the bolts (1a) fixing the EGR pipe (1b) to the exhaust manifold.

2. Undo the connector (2a) and disconnect the engine oil supply pipe (2b) from the turbocharger.

- Raise the vehicle.

See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.

1. Undo the connector (1a) from the retainer on the crankcase and remove the turbocharger engine oil supply pipe (1b).

Refitting

- Fit the turbocharger engine oil supply pipe and secure it to the crankcase using the connector.

- Lower the vehicle.

See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.

- Connect the turbocharger engine oil supply pipe and secure it with the connector tightened to torque.

- Tighten the bolts fixing the EGR pipe to the exhaust manifold.

- Fit the cold air intake to the connector on the air filter.

- Fit the upper front crossmember and tighten the fixing nuts to torque.

- Fit the bonnet lid lock complete with bracket and tighten the nuts fixing it to the upper crossmember and to the lower crossmember.

See in Op. 1016A10 SOUND-PROOFING COVER - R.R.

See in Op. 0010T11 ENGINE OIL - Check level and top up if necessary

- link 0010T11 missing