Workshop Manuals Factory service & repair MG
01 Introduction02 General information03 General data, torque settings and capacities04 Maintenance05 Engine (K Series)06 Engine management (MEMS 3), fuel and emission systems07 Cooling system08 Manifolds and exhaust system09 Clutch10 Manual gearbox11 Automatic gearbox (Stepspeed Em-CVT)12 Drive shafts13 Steering14 Front suspension15 Rear suspension16 Brakes17 Restraint systems (SRS)18 Body19 Heating and ventilation20 Air conditioning21 Wipers and washers22 Electrical23 Instruments
MG TF Factory Workshop Manual (2002-2005)02 · General information
02 · General

Dangerous substances

Make
MG
Model
TF Factory Workshop Manual
Year
2002–2005
Section
General precautions and fitting instructions › Dangerous substances
General informationDangerous substances

DANGEROUS SUBSTANCES

Modern vehicles contain many materials and liquids which if not handled with care can be hazardous to both personal health and the environment.

WARNING: Many liquids and other substances used in motor vehicles are poisonous and should not be consumed under any circumstances. As far as possible, ensure such substances are prevented from contact with the skin. These liquids and substances include but are not limited to: acid, anti-freeze, asbestos, brake fluid, fuel, windscreen washer additives, lubricants, refrigerant and various adhesives.

WARNING: Always read the instructions printed on labels or stamped on components and obey them implicitly. Such instructions are included for reasons of your health and personal safety. Never disregard them.

Synthetic rubber

Many ’O’ rings, seals, hoses, flexible pipes and other similar items which appear to be natural rubber, are in fact made of synthetic materials called Fluoroelastomers. Under normal operating conditions this material is safe and does not present a health hazard. However, if the material is damaged by fire or excessive heating, it can break down and produce highly corrosive Hydrofluoric acid.

Contact with Hydrofluoric acid can cause serious burns on contact with skin. If skin contact does occur:

  • Remove any contaminated clothing immediately.
  • Irrigate affected area of skin with a copious amount of cold water or limewater for 15 to 60 minutes.
  • Obtain medical assistance immediately.

Should any material be in a burnt or overheated condition, handle with extreme caution and wear protective clothing (seamless industrial gloves, protective apron etc.).

Decontaminate and dispose of gloves immediately after use.

Lubricating oils

Avoid excessive skin contact with used lubricating oils and always adhere to the health protection precautions.

WARNING: Avoid excessive skin contact with used engine oil. Used engine oil contains potentially harmful contaminants which may cause skin cancer or other serious skin disorders.

WARNING: Avoid excessive skin contact with mineral oil. Mineral oils remove the natural fats from the skin, leading to dryness, irritation and dermatitis.

Health Protection Precautions

  • Avoid prolonged and repeated contact with oils, particularly used engine oils.
  • Wear protective clothing, including impervious gloves where practicable.
  • Do not put oily rags in pockets.
  • Avoid contaminating clothes (particularly those next to the skin) with oil.
  • Overalls must be cleaned regularly. Discard heavily soiled clothing and oil impregnated footwear.
  • First aid treatment should be obtained immediately for open cuts and wounds.
  • Apply barrier creams before each work period, to help prevent lubricating oil from contaminating the skin.
  • Wash with soap and water to ensure all oil is removed (skin cleansers and nail brushes will help).
  • Use moisturisers after cleaning; preparations containing lanolin help replace the skin’s natural oils which have been removed.
  • Do not use petrol/gasoline, kerosene, diesel fuel, oil, thinners or solvents for cleaning skin.
  • If skin disorders develop, obtain medical advice without delay.
  • Where practicable, degrease components prior to handling.
  • Wear eye protection (e.g. goggles or face shield) if there is a risk of eye contamination. Eye wash facilities should be provided in close vicinity of the work area.

Parts & tools for this job For 2002 MG TF

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.