Power transmissionLayshaft: dismantling and assembling
| Layshaft: dismantling and assembling |

| Special tools and workshop equipment required |
| t
| Circlip opening pliers -A-81124- |
| t
| Set for exterior point clamps, housing tracks without exit -T20140- |
| t
| Gearbox extractor set -U-40100- |
| t
| Gear box repair set -U-40200A- |

Note!
| t
| Whenever new gears are fitted consult the technical data, → Chapter, Code letters, group numbers, ratios, filling quantities. |
| t
| If the layshaft, roller bearings or clutch housing are replaced, the layshaft should be adjusted → Chapter. |
| t
| To avoid premature wear and noise the roller bearings on a shaft should be replaced at the same time. |

| 6 - | Needle roller bearing |
|
q
| Dismantling and fitting → Chapter, Gearbox casing and gearbox selector shaft: repairing |
|
q
| Use tool -A-81124- to remove the safety ring |
|
q
| Determine thickness → Chapter, Assembly sequence |
|
q
| Use tool -A-81124- to remove the safety ring. |
|
q
| Fitting position → Chapter, Assembly sequence |
|
q
| Checking axial clearance → Chapter, Assembly sequence |
| 12 - | Needle bearing for sliding 2nd gear |
|
q
| Removing the bush → Chapter, Assembly sequence |
|
q
| Fitting the bush → Chapter, Assembly sequence |
| 13 - | Syncromesh ring 2nd gear |
| 14 - | Syncromesh assembly for 1st and 2nd gear |
| 15 - | Syncromesh ring 1st gear |
| 21 - | Needle roller bearing for 1st gear |
|
q
| Fitting position → Chapter, Assembly sequence |
| 25 - | Outer track, small roller bearing |
| 26 - | Small roller bearing |
|
q
| A matched pair with the driveshaft gear; they must be replaced together |
| 28 - | Large roller bearing |
|
q
| With the external roller bearing track and stop for reverse gear |
|
q
| Replace along with the roller bearings |
| Checking syncromesh ring wear |
| –
| Press the syncromesh ring onto the cone of the sliding gear and measure dimension “a” with a feeler gauge. |
|
|
|
| Syncromesh ring | Measurement “a” on a new syncromesh | Wear limit |
| 1st and 2nd gears | 1.1 ... 1.7 mm
| 0.5 mm
|
| Identification of syncromesh for 1st gear |
| Identification: 1 tooth missing -arrow- in three parts of the syncromesh ring. |
| This syncromesh ring can only be fitted to the 1st gear. |
|
|
|
| Removing the 1st and 2nd gear syncromesh assembly |
| Assembly position of the syncromesh hub: |
| The external indentification groove -arrow- should be aligned with the external teeth of the sliding sleeve. |
| –
| Slide the sleeve onto the syncromesh hub. |
| The recesses for the syncromesh locking keys and the sleeve must line up. |
|
|
|
| Removing the 1st and 2nd gear syncromesh assembly |
| –
| Insert the locking keys and fit the springs at 120° from each other. The angled ends of the springs must locate in the inner hollow of the corresponding locking keys. |
|
|
|
| Remove the outer track of the small roller bearing |
| –
| Remove the outer track of the small roller bearing with tool -T20140-. |
| –
| Procedure for extracting the outer ring → Chapter, General instructions for gearbox repairs. |
|
|
|
| Fit the outer track of the small roller bearing |
|
|
|
| Removing the small roller bearing |
| –
| Fit extractor -U-40100/4- below the small roller bearing on a press. With tool -U-40200A/4- over the lay shaft, dislodge the bearing. |
|
|
|
| Removing the large roller bearing |
| –
| Fit extractor -U-40100/4- below the large roller bearing on a press. |
|
|
|
| Fitting the small roller bearing |
| –
| Before fitting the small roller bearing on the layshaft, heat the inside track to 100 °C approx. |
| –
| Fit extractor -U-40100/3- to the layshaft under the crown gear on a press. With tool -U-40200A/19- side A fit the small bearing to its final position. |
|
|
|
| Fitting the large roller bearing |
| –
| Before fitting the big roller bearing on the layshaft, heat the inside track to 100 °C approx. |
| –
| Fit the layshaft on the large bearing and locate with tool -U-40200A/19- side B fitting as base extractor -U-40100/4-. |
|
|
|
01 Transmission
The same page in:
Leon Mk1.