Workshop Manuals Factory service & repair SEAT
01 Power transmission02 Running gear03 Body04 Power tramsmission05 Power unit06 Vehicle electrics07 Heating-ventilation-air conditioning system08 Automatic gearbox09 Engine, mixture preparation10 Engine, mechanics11 Manual gearbox12 Running gear - self diagnosis13 Heating and air conditioning14 Bodywork15 Heating, ventilation, air conditioning system
SEAT Leon Mk201 · Power transmission
01 · Transmission

Primary shaft: adjustment

Make
SEAT
Model
Leon Mk2
Section
085 5-speed manual gearshift › Gearbox,mechanics,gears,shafts,internal operation › Primary shaft: adjustment
Power transmissionPrimary shaft: adjustment
   
Primary shaft: adjustment
Diagram not available
Special tools and workshop equipment required
t  Universal tester stand -T20020-
t  Replacement parts extractors case -U-40100-
t  Replacement parts repair case -U-40200-

Adjust the primary shaft if any of these components have been replaced:
l  Gearbox casing.
l  Clutch casing.
l  Primary shaft.
l  Primary shaft tapered roller bearings.
To avoid unnecessary adjustment work, consult the Adjustments chart → Chapter.
   
–  Using tool -U-40200/11- and -U-40200/10-, fit the outer track of the primary shaft tapered roller bearing in the clutch casing without the adjusting washer.
–  Put the primary shaft in its housing in the gearbox casing.
–  Mount the clutch casing on the gearbox casing and screw in the securing bolts.
t  Tightening torque: 25 Nm
  Diagram not available
–  Set tool -T20020- with a tester onto the gearbox casing. Fit the end on to the primary shaft.
–  Give the primary shaft a few turns to seat the tapered roller bearings.
–  Adjust the tester to “0” with a pretension of 1 mm.
Primary shaft: adjustment – SEAT Leon Mk2  Note!
The adjustment of the tester to “0” must be repeated each time the measurement is done. If not, the tester will return to the initial position.
–  On the lower part of the gearbox, put pressure on the primary shaft in the direction of the tester.
–  Note the reading given on the tester (Example 1.21 mm).
Primary shaft: adjustment – SEAT Leon Mk2  Note!
The tester does not return to the initial position.
The necessary adjusting washer can be determined from the following table:
  Diagram not available
Adjusting washer chart
Set of bearingsAdjusting washer
Measurement (mm)Thickness (mm)Parts Nº
…0,66
0,67…0,68
0,69…0,70
0,650
0,675
0,700
085 311 391
085 311 391 N
085 311 391 A
0,71…0,73
0,74…0,75
0,76…0,78
0,725
0,750
0,775
085 311 391 P
085 311 391 B
085 311 391 Q
0,79…0,80
0,81…0,82
0,83…0,85
0,800
0,825
0,850
085 311 391 C
085 311 391 R
085 311 391 D
0,86…0,88
0,89…0,90
0,91…0,93
0,875
0,900
0,925
085 311 391 S
085 311 391 E
085 311 391 T
0,94…0,95
0,96…0,98
0,99…1,00
0,950
0,975
1,000
085 311 391 F
085 311 391 AA
085 311 391 G
1,01…1,03
1,04…1,05
1,06…1,08
1,025
1,050
1,075
085 311 391 AB
085 311 391 H
085 311 391 AC
1,09…1,10
1,11…1,13
1,14…1,16
1,100
1,125
1,150
085 311 391 J
085 311 391 AD
085 311 391 K
1,17…1,18
1,19…1,20
1,21…1,23
1,175
1,200
1,225
085 311 391 AE
085 311 391 L
085 311 391 AF
1,24…1,26
1,27…1,28
1,29…1,30
1,250
1,275
1,300
085 311 391 M
085 311 391 AG
085 311 391 AH
1,31…1,33
1,34…1,36
1,37…1,38
1,325
1,350
1,375
085 311 391 AJ
085 311 391 AK
085 311 391 AL
1,39…1,40
1,41…1,43
1,44…1.46
1,400
0,700 + 0,725
0,700 + 0,750
085 311 391 AM
085 311 391 A + P
085 311 391 A + B
1,47…1,48
1,49…1,50
1,51…1,53
0,700 + 0,775
0,700 + 0,800
0,700 + 0,825
085 311 391 A + Q
085 311 391 A + C
085 311 391 A + R
1,54... 1,56
1,57…1,58
1,59…1,61
0,700 + 0,850
0,700 + 0,875
0,700 + 0,900
085 311 391 A + D
085 311 391 A + S
085 311 391 A + E
1,62…1,63
1,64…1,66
1,67…1,68
1,69…1,70
0,700 + 0,925
0,700 + 0,950
0,700 + 0,975
0,700 + 1,000
085 311 391 A + T
085 311 391 A + F
085 311 391 A + AA
085 311 391 A + G

–  Once the necessary adjusting washer has been determined, detach the tester.
–  Take out the bolts securing both casings and detach the clutch casing.
–  Detach the primary shaft.
   
–  Using tool -U-40100/2-, detach the outer track of the primary shaft tapered roller bearing from the clutch casing.
–  Attach the adjusting washer with the calculated thickness (in this case, 1.225 mm) to the outer track tapered roller bearing housing.
  Diagram not available
–  Using tool -U-40200/10- and tool -U-40200/11-, attach the outer track of the primary shaft tapered roller bearing to the clutch casing.
–  Do a check measurement.
Check measurement
–  Put the primary shaft in its housing in the gearbox casing.
–  Mount the clutch casing on the gearbox casing and screw in the securing bolts.
t  Tightening torque: 25 Nm
  Diagram not available
–  Attach tool -T20020- with a tester to the gearbox casing. Fit the end on to the primary shaft.
–  Give the primary shaft a few turns to seat the tapered roller bearings.
–  Adjust the tester to “0” with a pretension of 1mm.
–  On the lower part of the gearbox, put pressure on the primary shaft in the direction of the tester.
–  The bearing play should oscillate between a minimum of 0.01 mm and a maximum of 0.10 mm.
Primary shaft: adjustment – SEAT Leon Mk2  Note!
The adjustment is correct when there is no play in the bearing but quite obvious play in the primary shaft that enables it to turn smoothly.
–  Maximum friction torque: 20 Ncm.
  Diagram not available

The same page in: Leon Mk1.

Parts & tools for this job For SEAT Leon

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.