Power transmissionSecondary shaft: dismounting and assembly
| Secondary shaft: dismounting and assembly |
| t
| If new pinions need to be fitted, consult the Identification Initials section, group assignment, reduction ratios, filling amounts → Chapter |
| t
| The secondary shaft must always be adjusted whenever components that may affect the position of the tapered roller bearings have been replaced. Consult the Adjustments chart → Chapter. |
Diagram not available| 2 - | Outer track, tapered roller bearing |
| 3 - | Tapered roller bearing |
|
q
| Detach, together with the 1st gear pinion → Fig. |
| 6 - | Needle bearing for 1st gear pinion |
| 7 - | Inner synchroniser ring for 1st gear |
|
q
| Check that the flanges show no signs of wear. |
| 8 - | Outer ring for 1st gear |
|
q
| Attach to the synchroniser ring for 1st gear → Item |
|
q
| Replace if there are signs of wear or grooves |
| 9 - | 1st gear synchroniser ring |
|
q
| When assembling, the ring flanges must fit into the housings of the 1st and 2nd gear synchroniser unit → Item |
| 11 - | Synchroniser unit for 1st and 2nd gears |
| 17 - | 2nd gear synchroniser ring |
| 18 - | Outer ring for 2nd gear |
|
q
| Attach to the synchroniser ring → Item |
|
q
| Replace if there are signs of wear or grooves. |
| 19 - | Inner synchroniser ring for 2nd gear |
|
q
| Check that there are no signs of wear on the flanges. |
| 22 - | Needle bearing for 2nd gear pinion |
|
q
| Assembly position: the identification notch must face the tapered unit. |
| 28 - | Tapered roller bearing |
| 29 - | Outer track, tapered roller bearing |
|
q
| For the secondary shaft. |
|
q
| The washer step should end up facing the tapered roller bearing. |
| 34 - | Needle bearing for 5th gear pinion |
| 36 - | 5th gear synchroniser ring |
|
q
| Fit to the 5th gear synchroniser ring. |
|
q
| Replace if it shows signs of wear. |
| 38 - | 5th gear synchroniser bush |
|
q
| Detachment, assembly and adjustment → Chapter onwards |
|
q
| Detachment, assembly and adjustment → Chapter onwards |
Diagram not available| Special tools and workshop equipment required |
| t
| Case for extractor tools for gearboxes -U-40100- |
| t
| Replacement parts repair case -U-40200- |
| t
| Pliers for opening elastic rings -A-81124- |
| Assembling the outer track of the tapered roller bearing |
| –
| Using tool -U-40200/10- and -U-40200/11-, attach the outer track of the tapered roller bearing to the gearbox casing. |

Note! | Attach the 1 mm thick washer between the outer track of the tapered roller bearing and the gearbox casing beforehand. |
|
|
Diagram not available
|
| Removing the tapered roller bearing together with the 1st gear pinion |
| –
| Attach tool -U-40100/3- under the 1st gear pinion. |
| –
| Set the secondary shaft - with tool -U-40100/3- installed - in a press and detach the bearing together with the 1st gear bearing. |
|
|
Diagram not available
|

Caution | The guard ring may forcefully spring off during dismounting. Prevent this from happening by placing a cloth or a protective screen behind the secondary shaft. Beware of accidents! |
|
|
|
Diagram not available
|
| Removing the synchroniser unit for 1st and 2nd gears |
| –
| Attach tool -U-40100/3- under the 2nd gear pinion. |
| –
| Set the secondary shaft - with tool -U-40100/3- installed - in a press and detach the synchroniser unit for 1st and 2nd gear. |
| –
| Detach the needle bearing for the 2nd gear pinion and the 3rd gear pinion. |
|
|
Diagram not available
|
| Removing the tapered roller bearing |
| –
| Attach tool -U-40100/4- under the bearing. |
| –
| Set the secondary shaft -with tool -U-40100/4- installed- in a press. |
| –
| Attach tool -U-40200/4- onto the secondary shaft and take out the bearing. |
|
|
Diagram not available
|
| Assembling the tapered roller bearing |
| –
| Attach tool -U-40100/3- under the driving pinion. |
| –
| Set the secondary shaft -with tool -U-40100/3- installed- in a press. |
| –
| Set tool -U-40200/19- side A onto the bearing and assemble. |
|
|
Diagram not available
|
| Removing the outer track of the tapered roller bearing |
| –
| Using tool -U-40100/2-, take the outer track of the secondary shaft tapered roller bearing off the clutch casing. |
|
|
Diagram not available
|
| Assembling the outer track of the tapered roller bearing |
| –
| Using tool -U-40200/12- and tool -U-40200/10-, fit the outer track of the tapered roller bearing in the clutch casing. |
|
|
Diagram not available
|

Note! | Tool -A-81124- can also be used. |
|
|
Diagram not available
|
| Checking the wear on the 1st and 2nd gear inner ring |
| –
| Before checking the wear, thoroughly clean the synchroniser rings and their corresponding pinions. |
| –
| Attach the inner ring to the 2nd gear pinion cone. Press the synchroniser ring onto the pinion and measure the height “a” with a gauge. |
|
|
Diagram not available
|
| Synchroniser ring | Measurement “a” with the new synchroniser | Limit of wear |
| 1st and 2nd gear | 0,75…1,25 mm | 0,3 mm |
| Checking the wear on the synchroniser ring for 1st and 2nd gear |
| –
| Before checking the wear, thoroughly clean the synchroniser rings and their corresponding pinions. |
| –
| Attach the inner and outer ring to the 2nd gear pinion cone. Press the synchroniser rings onto the pinion and measure the height “a” with a gauge. |
|
|
Diagram not available
|
| Synchroniser ring | Measurement “a” with the new synchroniser | Limit of wear |
| 1st and 2nd gear | 1,2…1,8 mm | 0,5 mm |
| Assembly position of the 2nd gear outer, inner and synchroniser rings |
| –
| Attach the inner ring -A- to the 2nd gear pinion. |
| The flange elbows -arrow 1- must face the outer ring -B-. |
| –
| Attach the outer ring -B-. |
| The flanges -arrow 2- must fit in the pinion grooves -arrow 3-. |
| –
| Attach the synchroniser ring -C-. |
| The grooves -arrow 4- fit with the inner ring -A- flange elbows -arrow 1-. |
|
|
Diagram not available
|
| Assembling the components of the 1st and 2nd gear synchroniser unit |
| –
| Attach the sliding sleeve -2- to the synchroniser bush -3- so that the grooves on both components coincide. |
| –
| Fit the cotters -4- and attach them with the springs -1-, with an offset of 120° between them. |
|
|
Diagram not available
|
| Assembling the components of the 1st and 2nd gear synchroniser unit |
| –
| The hooked end of both springs must fit into the corresponding cotter. |
|
|
Diagram not available
|
| Assembling the 1st and 2nd gear synchroniser unit |
| The neck -1- for the pin in the sliding sleeve must face the 1st gear pinion and the teeth -2- of the sleeve must face the 2nd gear pinion. |
| –
| Turn the synchroniser ring so that the blocking parts coincide with the housings of the synchroniser ring cotters. |
| –
| Use tools -U-40200/20- and -U-40100/3-. |
|
|
Diagram not available
|
| Assembly position of the 1st gear outer ring |
| The flanges -arrows- must face the reverse gear teeth -A-. |
|
|
Diagram not available
|
| Assembly position of the 1st gear inner ring |
| The flanges -1- must sit in the grooves -2- on the synchroniser ring -B-. |
| –
| Attach the needle bearing. |
|
|
Diagram not available
|
| Assembly position of the 1st gear inner ring |
| The grooves in the pinion cone -arrows- must fit into the flanges on the synchroniser ring → Fig.. |
|
|
Diagram not available
|
| Assembling the tapered roller bearing |
| –
| Attach the retainer washer. Use tools -U-40100/3- and -U-40200/15-. |
|
|
Diagram not available
|
01 Transmission
The same page in:
Leon Mk1.