Refitting (page 2 of 2)

(Op. 5505C26 continued)

• Fit the wiring and close the retaining strap.
• Reposition the engine coolant reservoir and screw the two fastening screws.
• Pass the wiring through the slot near the left headlamp housing.
• Pass the wiring through the slot near the right headlamp housing.
• Position and fix the wiring in the retaining strap along the front cross member.
• Connect the horn electrical connection.
• Connect the front/engine connection electrical connection and fix the wiring in the retaining strap.
• Connect the earth node on the engine and tighten the fastening nut.
• Connect the earth node on the left wheel housing and tighten the fastening screw.
• Position and fix the left turn indicator electric cable in its retaining strap.
• Connect the electrical connection of the thermometric switch on the radiator.
• Connect the fan electrical connection and fix the wiring in its retaining strap.
• Connect the rear window washer pump electrical connection.
• Connect the window washer pump electrical connection.
• Complete with Op. 5520C22 - SIDE REPEATER (ONE), LH OR RH - R.R.
• Fix the electric cable in the straps on the heel housing.
• Connect and fix the left fog lamp electric cable in the relevant straps.
• Repeat the operation for the right side.
• Complete with Op. 7055B42 - FRONT WHEEL HOUSING - R.R.
• Complete with Op. 4450B12 - FRONT WHEEL (TWO) - R.R.
• Complete with Op. 5550C30 - TURN INDICATOR (ONE), LH OR RH - R.R.
• Complete with Op. 554010 - HEADLIGHT (ONE), LH OR RH - R.R.
• Fix the wiring bundles in the straps on the strut.
• Connect the brake liquid level sensor(switch) electrical connection.
• Fit the 7.5A fuse socket on the group fastened on the ECU support bracket.
• Fit the fuse guard.
• Connect the air intake actuator electrical connection.
• Connect the front/air conditioner-heater electrical connections.
• Connect the passenger compartment air fan adjustment resistor electrical connection.
• Complete with Op. 5050B38 - FRONT WINDSCREEN WIPER UNIT - R.R or repair
• Complete with Op. 5050B32 - FRONT WINDOW WIPER ARM/S - R.R.
• Position the injection ECU support bracket and tighten the three fastening screws.
• Complete with Op. 5010B20 - CLIMATE CONTROL GROUP BULKHEAD - R.R.
• Complete with Op. 5010B23 - SEAL ON CLIMATE CONTROL COMPARTMENT BULKHEAD - R.R.
• Complete with Op. 1048A10 - COMPLETE AIR CLEANER - R.R.
• Reposition the wiring in the straps along the front right pillar and along the roof panel.
• Repeat the operation for the left side of the passenger compartment.
• Complete with Op. 7040H10 - ROOF PANEL TRIM - R.R.
• Complete with Op. 7065C30 - GRAB HANDLE (ONE), LH OR RH INSIDE PASSENGER COMPARTMENT - R.R.
• Complete with Op. 7065C34 - SUNSCREEN VISOR (ONE), LH OR RH - R.R.
• Complete with Op. 7065C68 - DRIVING MIRROR - r.r.
• Complete with Op. 7040E10 - CEILING LIGHT - R.R.
• Complete with Op. 7055A62 -PILLAR MOULDING, LH OR RH - R.R.
• Complete with Op. 7040H30 - FRONT PILLAR TRIM (ONE), LH OR RH - R.R.
• Complete with Op. 7040E66 - COURTESY LIGHT SWITCH(ONE) ON FRONT DOOR FRAME - R.R.
• Raise the passenger compartment carpet, pass the cigar lighter electric wiring and bring it near to the tunnel trim.
• Complete with Op. 7040L20 - TUNNEL TRIM - R.R.
• Complete with Op. 7065C42 - ASHTRAY (ONE) - R.R.
• Complete with Op. 7065C72 - FRONT CIGAR LIGHTER HOUSING - R.R.
• Raise the trim and pass the inertia switch electric cable and bring it near to the pedal group.
• Position the support bracket with the inertia switch, and tighten the two fastening nuts.

• Connect the inertia switch electrical connection.
• Place the various cables in the retaining straps.
• Assemble the foot rest platform.
• Fit the soundproofing trim and fasten the relevant buttons.
• Fit the passenger compartment carpet on the front left pillar and tighten the fastening buttons.

(Cont.)