Cylinder head(s) – cylinder head/s - various operations
- Make
- Lancia
- Model
- Thesis Factory Service Manual
- Year
- 2002–2009
- Section
- Engine › Cylinder head(s) – cylinder head/s - various operations
‹ Prev Cylinder head(s) – single cylinder head - removing and refittingNext › Crankshaft and flywheel – crankshaft
Tightening torquesCylinder head(s) – cylinder head/s - various operations
CYLINDER HEAD(S) – CYLINDER HEAD/S - VARIOUS OPERATIONS
| Value - daNm | Fastening | Component | Ø | Validity |
|---|---|---|---|---|
| 0,8 - 1,2 | OIL LEVEL DIPSTICK PIPE | 2.4 JTD 10V | ||
| (cylinder head side) 1.4 - 2.0 | Bolt | CAMSHAFT CAPS | M7 | 2.4 JTD 10V |
| (cylinder head side) 1.4 - 2.0 | Bolt | CAMSHAFT CAPS | M7 | 2.4 JTD 10V |
| 0,8 - 1,2 | OIL LEVEL DIPSTICK PIPE | 2.4 JTD 10V | ||
| 0,8 - 1,2 | OIL LEVEL DIPSTICK PIPE | 2.4 JTD 10V | ||
| (cylinder head side) 1.4 - 2.0 | Bolt | CAMSHAFT CAPS | M7 | 2.4 JTD 10V |
| (cylinder head side) 1.4 - 2.0 | Bolt | CAMSHAFT CAPS | M7 | 2.4 JTD 10V |
| (camshaft side) 0.9 -2.0 | Bolt | CAMSHAFT CAPS | 2.4 JTD 10V | |
| (camshaft side) 0.9 -2.0 | Bolt | CAMSHAFT CAPS | 2.4 JTD 10V | |
| (camshaft side) 0.9 -2.0 | Bolt | CAMSHAFT CAPS | 2.4 JTD 10V | |
| 1.4 -1.8 (cylinder head side) | HEATER PLUGS PREHEATING | M12 | 2.4 JTD 10V | |
| 1.4 -1.8 (cylinder head side) | HEATER PLUGS PREHEATING | M12 | 2.4 JTD 10V | |
| 1.4 -1.8 (cylinder head side) | HEATER PLUGS PREHEATING | M12 | 2.4 JTD 10V | |
| 2.7 -4.0 (cylinder head side) | Nut | INJECTORS(Petrol) | M8 | 2.4 JTD 10V |
| 2.7 -4.0 (cylinder head side) | Nut | INJECTORS(Petrol) | M8 | 2.4 JTD 10V |
| 2.7 -4.0 (cylinder head side) | Nut | INJECTORS(Petrol) | M8 | 2.4 JTD 10V |
| 2.3 - 3.3 | Bolt | WATER PUMP | M8 | 2.4 JTD 10V |
| 2.3 - 3.3 | Bolt | WATER PUMP | M8 | 2.4 JTD 10V |
| 0.9 ÷ 1.2 | Bolt | CAM ANGLE SENSOR | 2.4 JTD 10V | |
| 11.0 ÷ 15.9 | Bolt | TOOTHED DRIVEN PULLEY | M12 | 2.4 JTD 10V |
| 11.0 ÷ 15.9 | Bolt | TOOTHED DRIVEN PULLEY | M12 | 2.4 JTD 10V |
| 1.4 - 2.0 | Bolt | THERMOSTAT | M8 | 2.4 JTD 10V |
| 1.4 - 2.0 | Bolt | THERMOSTAT | M8 | 2.4 JTD 10V |
| 2.3 ÷ 3.3 | Bolt | VACUUM UNIT | M6 | 2.4 JTD 10V |
| 2.3 ÷ 3.3 | Bolt | VACUUM UNIT | M6 | 2.4 JTD 10V |
| 0.9 - 1.2 | Bolt | COOLANT PUMP RIGID INLET PIPE | M6 | 2.4 JTD 10V |
| 0.9 - 1.2 | Bolt | COOLANT PUMP RIGID INLET PIPE | M6 | 2.4 JTD 10V |
| 2.3 - 3.3 | Nut | INLET MANIFOLD | 2.4 JTD 10V | |
| 0.2 - 0.4 | Nuts | CONNECTOR FOR GLOW PLUGS | 2.4 JTD 10V | |
| 2.2 (injector side) | Connector | PIPES FROM FUEL MANIFOLD TO INJECTORS | M12 | 2.4 JTD 10V |
| 2.2 (injector side) | Connector | PIPES FROM FUEL MANIFOLD TO INJECTORS | M12 | 2.4 JTD 10V |
| 2.2 (injector side) | Connector | PIPES FROM FUEL MANIFOLD TO INJECTORS | M12 | 2.4 JTD 10V |
| 2.2 (manifold side) | Connector | PIPES FROM FUEL MANIFOLD TO INJECTORS | M14 | 2.4 JTD 10V |
| 2.2 (manifold side) | Connector | PIPES FROM FUEL MANIFOLD TO INJECTORS | M14 | 2.4 JTD 10V |
‹ Prev Cylinder head(s) – single cylinder head - removing and refittingNext › Crankshaft and flywheel – crankshaft
Parts & tools for this job For 2002 Lancia Thesis
- PARTEngine gasket setSearch: Lancia Thesis 2002 engine gasket set
- TOOLTorque wrenchSearch: 3/8 inch torque wrench
- TOOLFeeler gauge setSearch: feeler gauge set
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.