- Vectra B Workshop Manual
- General Vehicle Information
- A Maintenance, Body and Chassis Sheet Metal Parts, Frame
- B Paint
- C Body Equipment
- D Heating, Ventilation, Air Conditioning (HVAC)
- E Front Wheel Suspension, Wheels and Tyres
- F Rear Axle and Rear Wheel Suspension
- H Brakes
- J Engine and Engine Aggregates
- Repair Instructions
- Description and Operation
- Labour Time Allowances
- Other Information
- Technical Service Bulletins
- Technical Information
- OHC Petrol Engine
- Repair Instructions
- Radiator, Remove and Install (Without Air Conditioning)
- Thermostat, Remove and Install (16 LZ2 and 20 NEJ)
- DIS Ignition Module, Remove and Install reinstallation
- Fuel Pressure Regulator, Remove and Install
- Hot Film Mass Air Flow Meter, Remove and Install
- Throttle Valve Injection Housing, Remove and Install
- Throttle Valve Injection Housing, Upper Part, Remove and Install
- Fuel Pressure, Check
- Ignition Module, Remove and Install (16 LZ2)
- Cooling System - Cooling System, Top Up and Bleed
- Cooling System, Check for Leaks
- Fan Motor, Remove and Install
- Radiator (With Air Conditioning), Remove and Install
- Thermostat, Remove and Install (X 16 SZR)
- Seal Ring, Cylinder Head Thermostat Housing, Replace (16 LZ2 and 20 NEJ) NEJ)
- Coolant Pump, Remove and Install
- Engine Management System Motronic M 1. 5.4 - Engine Compartment Survey (20 NEJ)
- Wiring Harness Routing, Motronic M 1.5. 4
- Throttle Valve Potentiometer, Remove and Install
- Throttle Body, Remove and Install
- Injectors, Remove and Install reinstallation
- Crankshaft Pulse Pick-up, Remove and Install
- Knock Sensor, Remove and Install
- Idle Speed Adjuster, Remove and Install
- Injection System Relay, Remove and Install
- Fuel Pump Relay, Remove and Install reinstallation
- Intake Air Temperature Sensor, Remove and Install
- Coolant Temperature Sensor, Remove and Install
- Engine Control Unit, Remove and Install reinstallation
- Tank Vent Valve, Remove and Install reinstallation
- Engine Management System Multec Central Fuel Injection - Engine Compartment Survey (X 16 SZR)
- Engine Compartment Survey (16 LZ2)
- Wiring Harness Routing, Multec Central Fuel Injection
- Intake Air Pre-heating, Check
- DIS Ignition Module, Remove and Install (X 16 SZR)
- High Voltage Distributor, Remove and Install (16 LZ2)
- Throttle Valve Potentiometer, Remove and Install
- Intake Manifold Pressure Sensor, Remove and Install
- Injection Valve, Remove and Install reinstallation
- Crankshaft Pulse Pick-up, Remove and Install
- Knock Sensor, Remove and Install (X 16 SZR)
- Fuel Pressure Regulator / Fuel Pressure Regulator Diaphragm, Remove and Install
- Fuel Pump Relay, Remove and Install reinstallation
- Oxygen Sensor, Remove and Install (X 16 SZR)
- Idle Speed Stepper Motor, Remove and Install
- Octane Number Plug, Set Code (16 LZ2)
- Program Memory, Remove and Install (16 LZ2)
- Coolant Temperature Sensor, Remove and Install
- Tank Vent Valve, Remove and Install (X 16 SZR)
- Ignition Coil, Remove and Install (16 LZ2)
- Starter - Starter, Remove and Install (X16SZR)
- Starter, Remove and Install (16 LZ2 and 20 NEJ)
- Description and Operation
- Component Locator
- Labour Time Allowances
- Diagnostic Information and Procedures
- Technical Information
- General
- Seals and Seal Rings
- Ribbed V-Belt
- Fuel Pump
- Engine Damping Block
- Oil Circulating
- Timing Gear Case
- Cylinder Block
- Cylinder Head
- DOHC Petrol Engine
- Diesel Engine
- Fuel Injection Systems
- Engine Electrics
- Cooling System
- Turbo-Charging
- K Clutch and Transmission
- L Fuel and Exhaust System
- M Steering
- N Electrical Equipment and Instruments
- R Accessories