22 · Diagnostics

Horns not working

Make: Fiat
Model: Grande Punto Factory Service Manual
Year: 2005–2012
Section: Radio and accessories etc.. › Horns not working

‹ Prev Media player not working Next › Horns working out of tune

Fault diagnosisHorns not working

HORNS NOT WORKING

0	PRELIMINARY CHECKS	All OK	Problems encountered	Operation
		Results of the tests
	Check, by operating the horn control on the steering wheel, that the travel is correct	Move on to Step 1	Travel not correct	Remove the steering wheel and check that there are no impediments to the travel. Op. 4110A10 STEERING WHEEL - R+R FOR REPLACEMENT OR CHECKS If there are problems, replace the faulty component
1	CHECK ON INTERVENTION OF FUSE	All OK	Problems encountered	Operation
	Check that the horn protective fuse has not blown. It can be found in the engine compartment junction unit and is the third fuse in the first row F10 (15 A)	Move on to Step 2	The fuse has blown	Replace the fuse and search for the cause of the problem
2	RELAY CHECK	All OK	Problems encountered	Operation
	Swap the relay for the horns T3 (20A) with the one for the main beam headlamps T2 and check that the horns work	Move on to Step 3	The horn continues not to work	Restore the relays to their places and move on to Step 4
3	RELAY CHECK	All OK	Problems encountered	Operation
	Check that the main beam headlamps are working. If the result is positive, remove the horn relay feed and check that the contacts do not show signs of oxidation or deformation	End of diagnosis	1. The high beams do not work 2. There are irregularities at the engine compartment junction unit contacts	1. Replace the main beam headlamp relay (which was originally the one for the horns) 2. Renew the contacts. If necessary, replace the engine compartment junction unit Op. 5505A13 ADDITIONAL JUNCTION UNIT IN ENGINE COMPARTMENT - R.R.
4	RELAY ELECTRICAL CHECK	All OK	Problems encountered	Operation
	Undo the fastenings for the engine compartment junction unit and check, using a tester, that the power supply and the earth for the horn relay feed are correct Op. 5505A13 ADDITIONAL JUNCTION UNIT IN ENGINE COMPARTMENT - R.R.	Move on to Step 5	Relay line electrical problems	Move on to Step 8
5	HORN ELECTRICAL CHECK	All OK	Problems encountered	Operation
	Using a tester, connect to the horn power supply line and check that whilst the horn is working the supply voltage is more than 11.4 V. Also check the continuity and the insulation of the line	Move on to Step 6	1. The voltage is below 11.4 V 2. Other electrical problems	1. Check the cause of the power supply and restore the correct power supply. Possibly See table B015 ENGINE DOES NOT START (STARTER MOTOR WORKING) 2. Restore the correct electrical connections See E3010 HORNS
6	CHECK POSITIONING OF HORNS	All OK	Problems encountered	Operation
	Check that both the horn casing and the bracket are not touching or are not in the immediate vicinity (less than 10 mm) of other objects (other components, cables, pipes, etc.)	Move on to Step 7	Horn bracket or casing interfering with other components	Eliminate the cause of the interference
7	STEERING COLUMN SWITCH UNIT CHECK	All OK	Problems encountered	Operation
	Remove the steering wheel and check that there is nothing preventing the operation of the horn control switch. Using a tester in parallel to the switch check that, whilst it is working, the supply voltage is more than 11.4 V	Move on to Step 9	1. Switch stuck open 2. Switch power supply problems	1. Replace the steering wheel Op. 4110A10 STEERING WHEEL - R+R FOR REPLACEMENT OR CHECKS 2. Replace the steering column switch unit. Op. 5550A10 STALK UNIT ASSEMBLY - R+R
8	HORN CHECK	All OK	Problems encountered	Operation
	Remove the horn and connect it directly to a battery charger. Op. 5550B30 L/H OR R/H HORN (ONE) - R+R Check that a sound produced and that there are no unpleasant noises (knocking/buzzing)	Move on to Step 9	Sound faulty or no sound produced	Replace the horn Op. 5550B30 L/H OR R/H HORN (ONE) - R+R
9	ELECTRICAL CIRCUIT CHECK	All OK	Problems encountered	Operation
	The problem is due to the presence of an irregular electrical absorption source in the electrical equipment. Search for and eliminate this cause if necessary we will process suitable diagnoses for the battery, alternator and wiring	End of diagnosis	The fault persists	Contact technical service for further information on the problem

‹ Prev Media player not working Next › Horns working out of tune

Parts & tools for this job For 2005 Fiat Grande Punto

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.