Workshop Manuals Factory service & repair Nissan and Datsun
01 cover02 A (intro)03 B (CA18DET/ECCS)04 C (driveline)05 D (body & frame)06 E (interior electric)07 F (misc. codes)08 manual notes09 Front cover10 CONTENTS11 GI General information12 MA maintenance13 EM engine mechanical14 LC lubrication & cooling15 EF &EC engine fuel & emission control system16 FE engine control fuel & exhaust systems17 CL clutch18 MT manual transmission19 AT automatic transmission20 PD prop shaft & diff carrier21 FA front axle & suspension22 RA rear axle & suspension23 BR brake system24 ST steering25 BF body26 HA heater & aircon27 EL electrical system
Nissan and Datsun Nissan 180SX S13 1989 Workshop Manual23 · BR brake system
23 · Brakes

FA ® : PBC. (Poly Butyl Cuprysil) - Nissan 180SX S13 Workshop Manual

Make
Nissan and Datsun
Model
180SX Nissan 180SX S13 1989 Workshop Manual
Section
General › FA ® : PBC. (Poly Butyl Cuprysil) - Nissan 180SX S13 Workshop Manual
BR brake systemFA ® : PBC. (Poly Butyl Cuprysil) - Nissan 180SX S13 Workshop Manual

FA ® : PBC. (Poly Butyl Cuprysil)

REAR DISC BRAKE (CL9H) — Caliper

Copper washer 6% e9 17 -20(1,7 - 2.0, 12-14) Air bleeder a al 7 -9 {0.7 -0.9,5.1 - 6.5) Pin boit 122.32 @ () 22 - 31 (2.2 -3.2, - 16 - 23) > ay Cam KERR) Cylinder body Ro . “ a Cam poet | : Nem (kg-m, ft-Ib} ~ VG Or Return spring

FA ® : PBC. (Poly Butyl Cuprysil)

() 22 - 31 (2.2 -3.2,

a4 @ ee washer

grease or silicon-based

j ew 16 - 23) ¥| &@ 2 be . 23 25 -3.0, grease point YS L- | ~ 7 Eon @ <= Rubber grease point A a Cable stay @ = + Brake fluid point : “1 eat AY Rod EE ®) - Torque member \o ; a-O 26 - 36 (2.7 - 3.7, 20 - 27) fixing bolt ving EEB®) (2) 38 -52 (3.9 -5.3, 28 - 38) Le Ae Push rod Ea®) . > ow

Key plate

Ly y Piston seal ><) ® Inner shim oa

Ring C

1) eee Ring A Seat

Xe Spacer

Spring A Spring cover ° SS

2o— sings ,

. a Wave washer =

Y rae

Spacer Ball bearing NL “ Se, Adjusting nut LL Cup (ES ® Piston JF ® Outer shim ~ — ° Pad Torque member iston boot es Eh retainer KEE ®) SBR4814

Pad Replacement

CAUTION: When cylinder body is swung up, do not depress brake pedal because piston will pop out. @ Remove parking cable stay fixing bolt, pin bolts and lock spring. Then remove pad retainers, pads and shims.

@ When installing pads, retract piston into cylinder body by turning it clockwise.

CAUTION: Be careful not to damage piston boot or get oil on rotor. Always replace shims when replacing pads.

SBR641 BR-18

Parts & tools for this job For Nissan 180SX

As an Amazon Associate we earn from qualifying purchases.