Power transmissionGear change: removing and installing
| –
| With the ignition switched off disconnect battery earth strap. |

Note! | For vehicles fitted with a coded radio, first check the anti-theft code. |
| –
| Disassembling the upper engine casing. |
|
|
|
| –
| Remove the air filter, if fitted on the left of the engine bay. |
| –
| Release the air temperature sender connector. |
| –
| Remove the air filter vacuum hose. |
| –
| Release the inlet manifold hose. |
| –
| Remove the air filter securing bolts -arrows-. |
| –
| Remove the air filter complete with the inlet hose. |
|
|
|
| –
| Remove the speedometer sender connector -arrow 1-. |
| –
| Separate the reversing light connector -arrow 2-. |
| –
| Remove the earth cable from the engine to gearbox bolt. |
| –
| Remove the upper bolts that secure the engine to the gearbox. |
|
|
|
| –
| Separate the control rod (with counterweight) -A- from the selector rod and move to one side. |
| –
| Remove the short selector rod -B- by levering. First open the clip. |
|
|
|
| –
| Remove the long selection rod -C- from the coupling lever. First open the clip. |
|
|
|
| –
| Remove the two upper bolts -arrows- from the left console for the gearbox support. |
| –
| Remove the central bolt that joins the central console to the left hand side elastic bush of the engine. |
|
|
|
| –
| Separate the electric connections and cables from the starter motor cable support -arrow 1-. |
| –
| Separate the starter motor electric cables. |
| –
| Remove the bolt securing the starter motor cable support -arrow 2- and remove the support. |
| –
| Remove the upper bolt -arrow 2- from the starter motor. |
|
|
|
| –
| Remove the bolt securing the front engine support -arrow-. |
|
|
|
| –
| Remove the central bolt -arrow- from the rear right console, from the engine to the sub-frame. |
|
|
|
| –
| Fit Support assembly -U-30025B-. |

Note! | Remove all cable brackets, cables and hoses that could interfere with the fitting of the support tool. |
| –
| Tension the spindles of support tool -U-30025B-. |
|
|
|
| –
| Remove the clutch coil with a piece of wire -arrows- and do not open the passages. |

Note! | Do not depress the clutch pedal. |
|
|
|
| –
| Unbolt the PAS pipe bracket -arrow 1-. |

Note! | t
| To keep the connections out of the way tie them to the bodywork or some other element with a piece of string or wire |
| t
| The connections must be pulled aside without twisting or stretching them, so that they are out of the way when removing and fitting the gearbox |
| –
| Separate the front console from the elastic bush. |
| –
| Remove the lower bolts fron the engine/gearbox joint -arrow 2-. |
|
|
|
| –
| Remove the lower securing bolt of the rear left console to gearbox -arrow- and remove the console. |
|
|
|
| –
| Removing the counterweight -A- from the sub-frame. Mark fitting position. |
| –
| Remove the protective cover for the driveshaft. |
|
|
|
| –
| Remove the flywheel small protective cover -A-, located behind the right-hand articulation flange -arrows- (if fitted). |
| –
| Tilt the engine slightly by turning the -U-30025 B- support tool left-hand spindle. |
|
|
|
| –
| Locate the -SAT 1001 A- engine and gearbox jack under the gearbox so that the gearbox is supported. |
| –
| Remove the lower bolt, interior side, joining engine/gearbox. |
| –
| With the help of another mechanic, release the gearbox from the centring bushes, move it slightly upwards and turn it backwards to free the right-hand articulation flange from the flywheel. Remove the gearbox, taking care not to damage any element. |

Note! | On lowering the gearbox be careful with the PAS pipe. |
|
|
|
01 Transmission
The same page in:
Leon Mk2.