Workshop Manuals Factory service & repair Fiat
01 General information02 Specifications03 Manufacturing data and tolerances04 Tightening torques05 Fluids and lubricants06 Maintenance07 Diagnostic checks08 Engine09 Clutch10 Gearbox and differential11 Axles and driveshafts12 Brakes13 Steering14 Suspension and wheels15 Heating, air conditioning and auxiliary units16 Electrical equipment17 Body fittings18 Body panels and frame19 Wiring diagrams and electrical functions20 Wiring harnesses21 Connectors and pin-outs22 Fault diagnosis23 Special tools
Fiat Bravo Factory Service Manual (2007-2014)14 · Suspension and wheels
14 · Steering & suspension

Rear suspension axle/crossmember bushes - r.r.

Make
Fiat
Model
Bravo Factory Service Manual
Year
2007–2014
Section
Rear suspension › Rear suspension axle/crossmember bushes - r.r.
Suspension and wheelsRear suspension axle/crossmember bushes - r.r.

REAR SUSPENSION AXLE/CROSSMEMBER BUSHES - R.R.

Operation 4420D48 · REAR SUSPENSION AXLE/CROSSMEMBER

Removing

Op. 4450B13 REAR WHEELS (TWO) - R.R

Op. 7055B80 UNDERBODY SIDE PROTECTION (ONE) LEFT OR RIGHT - R.R.

Op. 7040L20 TUNNEL COVER - R.R

- Disconnect the handbrake cables from the brake caliper and from the intermediate supports on the axle, with reference to

Op. 3380A36 LEFT HANDBRAKE CONTROL CABLE - R.R.

Op. 3380A37 RIGHT HANDBRAKE CONTROL CABLE - R.R.

- Disconnect the electrical connections for the rear wheel sensors, with reference to

Op. 3340A34 LEFT OR RIGHT REAR WHEEL RPM SENSOR (ONE) - R.R.

- Unscrew the brake-clutch fluid reservoir plug and fit the tool.

ToolDescriptionFunctionValidity
2000001400PlugBrake/ clutch system vacuum

1. Undo the connector (1a), remove the clip (1b) and disconnect the flexible brake fluid pipe (1c) from the rigid pipe.

REAR SUSPENSION AXLE/CROSSMEMBER BUSHES - R.R.

- Proceed in the same way for the brake fluid pipe on the right side.

- Using the special equipment, proceed with the removal of the axle assembly and supports, with reference to

Op. 4420D10 REAR SUSPENSION AXLE - R+R INCLUDES BLEEDING

1. Fit the tool (1a) as illustrated and remove the bush (1b).

ToolDescriptionFunctionValidity
2000025800Extractor/ Fitting toolRemoving-refitting securing bush to the rear axle support
REAR SUSPENSION AXLE/CROSSMEMBER BUSHES - R.R.

- Proceed in the same way for the bush on the right side.

Refitting

- Avoid fitting the bushes at low temperatures (e.g.: outdoor workshop warehouse).

- It is advisable to fit the bushes at a low fitting speed, max. 10 mm per second.

- Follow the instructions below for fitting the bushes.

1. The axis between the bush (1a) splining should be parallel to the axle (1b) welding seam.

REAR SUSPENSION AXLE/CROSSMEMBER BUSHES - R.R.

1. Place the bush (1a) in position as described previously and fit it using the tool (1b).

ToolDescriptionFunctionValidity
2000025800Extractor/ Fitting toolRemoving-refitting securing bush to the rear axle support
REAR SUSPENSION AXLE/CROSSMEMBER BUSHES - R.R.

- Proceed in the same way for the bush on the right side.

- Proceed with refitting the axle supports and, using the special equipment, fit the axle assembly on the vehicle, with reference to

Op. 4420D10 REAR SUSPENSION AXLE - R+R INCLUDES BLEEDING

- Connect the flexible brake fluid pipes to the rigid pipes, tighten the connectors and fit the retaining clips.

- Connect the electrical connections for the rear wheel sensors, with reference to

Op. 3340A34 LEFT OR RIGHT REAR WHEEL RPM SENSOR (ONE) - R.R.

- Connect the handbrake cables to the brake caliper and to the intermediate supports on the axle, with reference to

Op. 3380A36 LEFT HANDBRAKE CONTROL CABLE - R.R.

Op. 3380A37 RIGHT HANDBRAKE CONTROL CABLE - R.R.

Op. 0010T64 BRAKE AND/OR CLUTCH FLUID CHECK LEVEL AND TOP UP AS NECESSARY

Op. 0010T65 HYDRAULIC BRAKE SYSTEM - BLEED AIR

Op. 3380A04 HANDBRAKE - ADJUST TRAVEL

Op. 7055B80 UNDERBODY SIDE PROTECTION (ONE) LEFT OR RIGHT - R.R.

Op. 4450B13 REAR WHEELS (TWO) - R.R

Op. 7040L20 TUNNEL COVER - R.R

Parts & tools for this job For 2007 Fiat Bravo

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.