Gearbox lower reaction rod ' -r.r.
- Make
- Fiat
- Model
- Stilo Factory Service Manual
- Year
- 2001–2007
- Section
- Power unit supports › Gearbox lower reaction rod ' -r.r.
GEARBOX LOWER REACTION ROD ' -R.R.
Removing
Place the vehicle on a ramp and raise it.
1. Undo the bolt fixing the bracke to the gearbox.
2. Undo the bolt (2a) fixing the crossmember and remove the reaction rod (2b).
Removing
Place the car on a ramp.
Raise the vehicle.
1. Undo the bolt fixing the reaction rod to the mounting bracket.
2. Undo the bolt (2a) fixing the frame and remove the reaction rod (2b).
Removing
Place the car on a lift.
Raise the car.
1. Release the flexible buffer for the flexible section of the exhaust pipe from the pin on the bodyshell.
2. Undo the bolt fixing the reaction rod to the mounting bracket.
3. Undo the bolt (3a) fixing it to the chassis and remove the reaction rod (3b).
Removing
Place the car on a ramp.
- 7055B54 under-engine guard - r r
1. Undo the bolt fixing the rod to the mounting bracket.
2. Undo the fixing bolt (2a) on the front suspension crossmember and remove the lower gearbox reaction rod (2b).
Refitting
Place the reaction rod back in its housing.
Tighten the bolt fixing the crossmember to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| Bolt | POWER UNIT BOTTOM REACTION ROD | M12 x 1.5 | (Crossmember side) 12,5 |
Position the bolt and tighten it to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| Nut | POWER UNIT BOTTOM REACTION ROD | M12 x 1.25 | (Gearbox side) 7 |
Refitting
Position the power unit lower reaction rod.
Tighten the bolt fixing the rod to the frame to torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| Bolt | REACTION ROD | M12 x 1.25 | 13.5 |
Tighten the bolt fixing the reaction rod to the mounting bracket to torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| Bolt | REACTION ROD | M12 x 1.25 | 7.5 |
Lower the vehicle.
Remove the car from the lift.
Refitting
Position the power unit lower reaction rod.
Tighten the bolt fixing the rod to the frame to torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| Bolt | REACTION ROD | M12 x 1.25 | 13.5 |
Tighten the bolt fixing the reaction rod to the mounting bracket to torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| Bolt | REACTION ROD | M12 x 1.25 | 7.5 |
Secure the flexible buffer for the flexible section of the exhaust pipe to the pin on the bodyshell.
Lower the vehicle.
Remove the vehicle from the lift.
Refitting
Fit the lower gearbox reaction rod.
Tighten the bolts fixing the rod to the gearbox to torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| Nut | LOWER ROD ON GEARBOX | M12 x 1.25 | 7.5 |
Tighten the bolts fixing the reaction rod to the suspension crossmember to torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| Bolt | LOWER ROD ON GEARBOX | M12 x 1.25 | 13.5 |
- 7055B54 under-engine guard - r r
Remove the vehicle from the lift.
Parts & tools for this job For 2001 Fiat Stilo
- PARTEngine gasket setSearch: Fiat Stilo 2001 engine gasket set
- TOOLTorque wrenchSearch: 3/8 inch torque wrench
- TOOLFeeler gauge setSearch: feeler gauge set
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.