- Vectra B Workshop Manual
- General Vehicle Information
- A Maintenance, Body and Chassis Sheet Metal Parts, Frame
- B Paint
- C Body Equipment
- D Heating, Ventilation, Air Conditioning (HVAC)
- E Front Wheel Suspension, Wheels and Tyres
- F Rear Axle and Rear Wheel Suspension
- H Brakes
- J Engine and Engine Aggregates
- Repair Instructions
- Description and Operation
- Labour Time Allowances
- Other Information
- Technical Service Bulletins
- Technical Information
- OHC Petrol Engine
- DOHC Petrol Engine
- Repair Instructions
- Description and Operation
- Diagnostic Information and Procedures
- Other Information
- Technical Service Bulletins
- Technical Information
- General
- Seals and Seal Rings
- Ribbed V-Belt
- Engine Damping Block
- Oil Circulating
- Timing Gear Case
- Cylinder Block
- Cylinder Head
- Repair Instructions
- Cylinder head and attaching parts, check and measure - Survey
- Cylinder head height, check
- Cylinder head, check for plane surface
- Valve, measure
- Inner diameter of valve guide, check
- Valve stem play, determine
- Installation height of valves, check
- Installation height of valve guide, check
- Cylinder head, overhaul
- Cylinder head, attach to assembly tool set KM-6215
- Cylinder head, disassemble
- Valves, remove
- Valve seat, cut (in cylinder head)
- Valve guide, ream
- Valve, grind
- Valve, grind in
- Valve stem seals, replace
- Cylinder head, assemble
- Cylinder head machining table of contents
- Toothed Belt Tension Roller, Remove and Install
- Toothed Belt Guide Roller, Remove and Install
- Intake Pipe (above Cylinders 2-4-6), Remove and Install
- Intake Bridge, Remove and Install Remove and Install
- Intake Flange, Remove and Install Remove and Install
- Compression, Check
- Pressure Loss, Check
- Exhaust Manifold, Remove and Install reinstallation
- Intake Manifold, Remove and Install reinstallation
- Toothed Belt Cover, Upper Part, Remove and Install
- Toothed Belt, Remove and Install
- Rear Toothed Belt Cover, Remove and Install
- Cylinder Head, Remove and Install (X 16 XEL)
- Intake Pipe (Above Cylinders 1-3-5), Remove and Install (X 25 XE)
- Intake Plenum, Remove and Install (X 25 XE)
- Exhaust Manifold (Cylinders 1-3-5), Remove and Install (X 25 XE)
- Exhaust Manifold (Cylinders 2-4-6), Remove and Install (X 25 XE)
- Intake Plenum Switchover Valves, Remove and Install
- Switchover Valve - Solenoid Valve, Remove and Install
- Toothed Belt Tension, Check
- Toothed Belt Tension, Adjust
- Exhaust Manifold, Remove and Install (X 16 XEL)
- Exhaust Manifold, Remove and Install (X 18 XE1)
- Inlet Manifold - Upper Part, Remove and Install (X 16 XEL with Secondary Air System)
- Inlet Manifold - Lower Part, Remove and Install (X 16 XEL with Secondary Air System)
- Flange - Intake Manifold, Remove and Install (X16XEL without Secondary Air System)
- Intake Manifold, Remove and Install (X16XEL without Secondary Air System) Y16XE)
- Intake Manifold, Remove and Install (X 18 XE1)
- Cylinder Head, Remove and Install (X18XE1, Z18XE, Z18XEL)
- Coolant Flange, Remove and Install (X18XE1, Z18XE, Z18XEL)
- Coolant Flange, Remove and Install (X16XEL without Secondary Air System, Y16XE, Z16XE)
- Specifications
- Special Tools and Equipment
- Other Information
- Technical Service Bulletins
- Hydraulic Valve Lifter
- Camshaft
- Valves
- Spark Plug
- Cylinder Head Housing
- Diesel Engine
- Fuel Injection Systems
- Engine Electrics
- Cooling System
- Turbo-Charging
- K Clutch and Transmission
- L Fuel and Exhaust System
- M Steering
- N Electrical Equipment and Instruments
- R Accessories