Privacy Policy
Donate and help keep workshop manuals freely available.
Other Vauxhall Workshop Service and Repair Manuals
Other Makes
Vectra B Workshop Manual
General Vehicle Information
A Maintenance, Body and Chassis Sheet Metal Parts, Frame
B Paint
C Body Equipment
D Heating, Ventilation, Air Conditioning (HVAC)
E Front Wheel Suspension, Wheels and Tyres
F Rear Axle and Rear Wheel Suspension
H Brakes
J Engine and Engine Aggregates
Repair Instructions
Description and Operation
Labour Time Allowances
Other Information
Technical Service Bulletins
Technical Information
OHC Petrol Engine
DOHC Petrol Engine
Repair Instructions
Description and Operation
Diagnostic Information and Procedures
Other Information
Technical Service Bulletins
Technical Information
General
Seals and Seal Rings
Ribbed V-Belt
Engine Damping Block
Oil Circulating
Timing Gear Case
Cylinder Block
Cylinder Head
Repair Instructions
Cylinder head and attaching parts, check and measure - Survey
Cylinder head height, check
Cylinder head, check for plane surface
Valve, measure
Inner diameter of valve guide, check
Valve stem play, determine
Installation height of valves, check
Installation height of valve guide, check
Cylinder head, overhaul
Cylinder head, attach to assembly tool set KM-6215
Cylinder head, disassemble
Valves, remove
Valve seat, cut (in cylinder head)
Valve guide, ream
Valve, grind
Valve, grind in
Valve stem seals, replace
Cylinder head, assemble
Cylinder head machining table of contents
Toothed Belt Tension Roller, Remove and Install
Toothed Belt Guide Roller, Remove and Install
Intake Pipe (above Cylinders 2-4-6), Remove and Install
Intake Bridge, Remove and Install Remove and Install
Intake Flange, Remove and Install Remove and Install
Compression, Check
Pressure Loss, Check
Exhaust Manifold, Remove and Install reinstallation
Intake Manifold, Remove and Install reinstallation
Toothed Belt Cover, Upper Part, Remove and Install
Toothed Belt, Remove and Install
Rear Toothed Belt Cover, Remove and Install
Cylinder Head, Remove and Install (X 16 XEL)
Intake Pipe (Above Cylinders 1-3-5), Remove and Install (X 25 XE)
Intake Plenum, Remove and Install (X 25 XE)
Exhaust Manifold (Cylinders 1-3-5), Remove and Install (X 25 XE)
Exhaust Manifold (Cylinders 2-4-6), Remove and Install (X 25 XE)
Intake Plenum Switchover Valves, Remove and Install
Switchover Valve - Solenoid Valve, Remove and Install
Toothed Belt Tension, Check
Toothed Belt Tension, Adjust
Exhaust Manifold, Remove and Install (X 16 XEL)
Exhaust Manifold, Remove and Install (X 18 XE1)
Inlet Manifold - Upper Part, Remove and Install (X 16 XEL with Secondary Air System)
Inlet Manifold - Lower Part, Remove and Install (X 16 XEL with Secondary Air System)
Flange - Intake Manifold, Remove and Install (X16XEL without Secondary Air System)
Intake Manifold, Remove and Install (X16XEL without Secondary Air System) Y16XE)
Intake Manifold, Remove and Install (X 18 XE1)
Cylinder Head, Remove and Install (X18XE1, Z18XE, Z18XEL)
Coolant Flange, Remove and Install (X18XE1, Z18XE, Z18XEL)
Coolant Flange, Remove and Install (X16XEL without Secondary Air System, Y16XE, Z16XE)
Specifications
Special Tools and Equipment
Other Information
Technical Service Bulletins
Hydraulic Valve Lifter
Camshaft
Valves
Spark Plug
Cylinder Head Housing
Diesel Engine
Fuel Injection Systems
Engine Electrics
Cooling System
Turbo-Charging
K Clutch and Transmission
L Fuel and Exhaust System
M Steering
N Electrical Equipment and Instruments
R Accessories