Workshop Manuals Factory service & repair Alfa Romeo
01 General information02 Specifications03 Manufacturing data and tolerances04 Tightening torques05 Fluids and lubricants06 Maintenance07 Diagnostic checks08 Engine09 Clutch10 Gearbox and differential11 Axles and driveshafts12 Brakes13 Steering14 Suspension and wheels15 Heating, air conditioning and auxiliary units16 Electrical equipment17 Body fittings18 Body panels and frame19 Wiring diagrams and electrical functions20 Wiring harnesses21 Connectors and pin-outs22 Fault diagnosis23 Special tools
Alfa Romeo 147 Factory Service Manual (2000-2004)08 · Engine
08 · Engine

Engine oil pump - r+r

Make
Alfa Romeo
Model
147 Factory Service Manual
Year
2000–2004
Section
Engine lubrication system › Engine oil pump - r+r
EngineEngine oil pump - r+r

Engine oil pump - r+r

Operation 1084B12 · Engine oil lubrication circuit

3.2 V6

Removing

Position the vehicle on the ramp.

Ensure that the ignition key is in the OFF position, then disconnect the negative battery terminal (-).

NameConnector
BatteryA1B

Proceed with removal - 4450B04 right front wheel r r.

Proceed with removal - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R..

Proceed with removal - 1092G10 single engine belt r r.

Proceed with removal - 7055B54 under-engine guard - r r.

Proceed with removal - 1076B82 left exhasust pipe between catalytic preconverter and converter r r.

Proceed with removal - 5510C34 rpm and timing sensor (single) - r+r.

Proceed with removal - 1020A20 crank case oil sump - r + r clean seals for sealant application.

1. Fit the crankshaft pulley counter-torque tool.

NameCountry
1Counter-torque for crankshaft1.870.646.000
Engine oil pump - r+r

1. Undo the bolt fixing the chain drive to the engine oil pump.

Engine oil pump - r+r

1. Release the chain drive (1a) from the engine oil pump using the tool (1b).

NameCountry
1bExtractor1.860.954.001

2. Undo the bolts (2a) and remove the engine oil pump (2b).

Engine oil pump - r+r

Refitting

1. Place the power assisted steering pump (1a) back in its housing and fix it tightening the bolts (1b) to the recommended torque.

FasteningComponentØ

Value

(daNm)

1bBoltENGINE OIL PUMPM10(Main journal cap side) 4.5 ÷ 5.5

2. Position the chain drive (2a) on the engine oil pump and secure it tightening the bolt (2b) to the recommended torque.

FasteningComponentØ

Value

(daNm)

2bBoltENGINE OIL PUMP DRIVE CHAINM10(Engine oil pump side) 4.5 ÷ 5.5
Engine oil pump - r+r

Remove the crankshaft pulley counter-torque tool.

NameCountry
Counter-torque for crankshaft1.870.646.000

Proceed with refitting - 1020A20 crank case oil sump - r + r clean seals for sealant application.

Proceed with refitting - 5510C34 rpm and timing sensor (single) - r+r.

Proceed with refitting - 1076B82 left exhasust pipe between catalytic preconverter and converter r r.

Proceed with refitting - 1092G10 single engine belt r r.

Proceed with refitting - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R..

Proceed with refitting - 4450B04 right front wheel r r.

Refill the engine oil lubrication system - 0010T11 engine oil check level and top up.

Proceed with refitting - 7055B54 under-engine guard - r r.

Connect the negative (-) battery terminal.

Remove the car from the ramps.

Parts & tools for this job For 2000 Alfa Romeo 147

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.