Emgine oil intake duct - r r

Operation 1084B26 · Engine oil lubrication circuit

1.6 TS

Removing

Position the vehicle on the ramp.

Ensure that the ignition key is in the OFF postition, then disconnect the battery negative terminal.

Proceed with the removal - 4450B10 Front WHEEL (one) - R.R. (Right side).

Proceed with the removal - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side).

Proceed with the removal - 1072C44 exhaust manifold heat shield on bulkhead - r+r.

1.6 TS · 103 CV

Proceed with the removal - 1080B62 catalytic converter - r + r.

1.6 TS · 120 CV

Proceed with the removal - 1080B40 catalytic pre-converter - r r.

1.6 TS

Proceed with the removal - 1008A44 rear rigid mount - r r.

Proceed with the removal - 1092G10 single engine belt r r.

Proceed with the removal - 1092A10 Crankshaft services PULLEY - R.R..

Proceed with the removal - 1020A20 crank case oil sump - r + r clean seals for sealant application.

1. Undo the bolts (1a) and remove the engine oil inlet (1b) complete with gasket.

Refitting

Place the engine oil inlet, complete with gasket, back in its housing and secure it tightening the bolts to the recommended torque.

Proceed with the refitting - 1020A20 crank case oil sump - r + r clean seals for sealant application.

Proceed with the refitting - 1092A10 Crankshaft services PULLEY - R.R..

Proceed with the refitting - 1092G10 single engine belt r r.

Proceed with the refitting - 1008A44 rear rigid mount - r r.

1.6 TS · 103 CV

Proceed with the refitting - 1080B62 catalytic converter - r + r.

1.6 TS · 120 CV

Proceed with the refitting - 1080B40 catalytic pre-converter - r r.

1.6 TS

Proceed with the refitting - 1072C44 exhaust manifold heat shield on bulkhead - r+r.

Proceed with the refitting - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side).

Proceed with the refitting - 4450B10 Front WHEEL (one) - R.R. (Right side).

Connect the battery terminal (-).

Refill the engine oil lubrication system - 1084A10 ENGINE OIL - Check level and top up, if necessary.

Remove the car from the ramp.

2.0 TS

Removing

Position the vehicle on the ramp.

Ensure that the ignition key is in the OFF postition, then disconnect the battery negative terminal.

Proceed with the removal - 4450B10 Front WHEEL (one) - R.R. (Right side).

Proceed with the removal - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side).

Proceed with the removal - 7055B54 under-engine guard - r r.

Proceed with the removal - 1072C44 exhaust manifold heat shield on bulkhead - r+r.

Proceed with the removal - 1080B40 catalytic pre-converter - r r.

Proceed with the removal - 1008A44 rear rigid mount - r r.

Proceed with the removal - 1092G10 single engine belt r r.

Proceed with the removal - 1092A10 Crankshaft services PULLEY - R.R..

Proceed with the removal - 1092G20 engine component single belt fixed tensioner - one - r + r.

Proceed with the removal - 1092G14 engine component single belt mobile tensioner - r + r.

Proceed with the removal - 1032D12 timing system protective cover(s) - r + r.

Proceed with the removal - 1020A20 crank case oil sump - r + r clean seals for sealant application.

1. Undo the bolts (1a) and remove the engine oil inlet (1b) complete with gasket.

Refitting

Place the engine oil inlet, complete with gasket, back in its housing and secure it tightening the bolts to the recommended torque.

Proceed with the refitting - 1020A20 crank case oil sump - r + r clean seals for sealant application.

Proceed with the refitting - 1032D12 timing system protective cover(s) - r + r.

Proceed with the refitting - 1092G14 engine component single belt mobile tensioner - r + r.

Proceed with the refitting - 1092G20 engine component single belt fixed tensioner - one - r + r.

Proceed with the refitting - 1092A10 Crankshaft services PULLEY - R.R..

Proceed with the refitting - 1092G10 single engine belt r r.

Proceed with the refitting - 1008A44 rear rigid mount - r r.

Proceed with the refitting - 1080B40 catalytic pre-converter - r r.

Proceed with the refitting - 1072C44 exhaust manifold heat shield on bulkhead - r+r.

Proceed with the refitting - 7055B54 under-engine guard - r r.

Proceed with the refitting - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side).

Proceed with the refitting - 4450B10 Front WHEEL (one) - R.R. (Right side).

Connect the battery terminal (-).

Refill the engine oil lubrication system - 1084A10 ENGINE OIL - Check level and top up, if necessary.

Remove the car from the ramp.

1.9 JTD 8V

Removing

- 4450B04 right front wheel r r

- 7055B54 under-engine guard - r r

- 1076B50 exhaust pipe attachment to engine - r + r

- 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R.

- 1092G10 single engine belt r r

- 2710A35 intermediate drive shaft mount - r r

- 1020A20 crank case oil sump - r + r clean seals for sealant application

- 1084B28 engine oil intake pump - r + r with crankcase sump removed

Refitting

- 1084B28 engine oil intake pump - r + r with crankcase sump removed

- 1020A20 crank case oil sump - r + r clean seals for sealant application

- 2710A35 intermediate drive shaft mount - r r

- 1092G10 single engine belt r r

- 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R.

- 1076B50 exhaust pipe attachment to engine - r + r

- 7055B54 under-engine guard - r r

- 4450B04 right front wheel r r

- 0010T11 engine oil check level and top up

1.9 JTD 16V

Removing

Proceed with removal - 7055B54 under-engine guard - r r.

Proceed with removal - 1016A10 sound-proofing cover - r + r.

Proceed with removal - 1084A16 oil dip stick pipe - r r.

Proceed with removal - 1020A20 crank case oil sump - r + r clean seals for sealant application.

Proceed with removal - 1084B28 engine oil intake pump - r + r with crankcase sump removed.

Refitting

Proceed with refitting - 1084B28 engine oil intake pump - r + r with crankcase sump removed.

Proceed with refitting - 1020A20 crank case oil sump - r + r clean seals for sealant application.

Proceed with refitting - 1084A16 oil dip stick pipe - r r.

Proceed with refitting - 0010T11 engine oil check level and top up.

Proceed with refitting - 1016A10 sound-proofing cover - r + r.

Proceed with refitting - 7055B54 under-engine guard - r r.