60,000KM SERVICE

Operation 0010K60 · PROGRAMMED MAINTENANCE, EMISSION CONTROL VERSIONS UP TO 90,000KM

1.3 Multijet, 1.9 Multijet

- Check the tyre tread is not worn.

Some types of tyre are fitted with wear gauges; they should be replaced as soon as these gauges are visible on the tread.

Do not swap tyres across.

- Check the tyre inflation pressure is correct. Also check the spare wheel.

The tyre pressures must be checked when they are cold.

- Check that the lighting system is operating correctly: headlamps, turn signals, hazard lights, luggage compartment lights, passenger compartment light and instrument panel warnings lights.

- Check the windscreen wiper system is operating correctly and adjust the sprays if necessary.

- Check the front and rear wiper blades are correctly positioned and not worn.

- Check condition and wear on front disc brake pads, rear pads (where present) and operation of pad wear indicator

- Check rear drum brake linings condition and wear (1.3 Multijet version)

- Carry out a visual check of: exterior bodywork, underbody protection, rigid and flexible pipes (exhaust - fuel system - braking system) rubber elements (boots - hoses - bushes - etc.)

- Check cleanliness of locks, bonnet and boot lids, cleanliness and lubrication of linkage

- Visually inspect the condition of the accessory drivebelt.

- Check and if necessary adjust the handbrake lever travel; refer to

Op. 3380A04 HANDBRAKE - ADJUST TRAVEL

- Check and adjust the tappet clearance (1.9 Multijet version); refer to

Op. 1036H14 VALVE TAPPETS - CHECK CLEARANCE

Op. 1036H10 VALVE TAPPETS - CHECK AND ADJUST CLEARANCE, IF NECESSARY

- Check exhaust emissions; refer to

Op. 1080A20 EXHAUST FUMES - CHECK WITH OPACIMETER

- Replace the fuel filter; refer to

Op. 1044B10 FUEL FILTER ASSEMBLY - R + R OR REPLACE

- Replace the air cartridge filter; refer to

Op. 1048A14 AIR CLEANER FILTER ELEMENT - REPLACE.

- Restore the brake-clutch fluid level; refer to

Op. 0010T64 BRAKE AND/OR CLUTCH FLUID CHECK LEVEL AND TOP UP AS NECESSARY

- Restore the engine coolant level; refer to

Op. 0010T21 ENGINE COOLANT - CHECK DENSITY AND CHANGE, IF NECESSARY

- Restore the battery fluid, windscreen washer fluid level, etc.

- Check the operation of the engine control systems (using the diagnostic socket).

- Change engine oil and oil filter (or every 24 months); refer to

Op. 0010T12 ENGINE OIL AND FILTER - REPLACE

Only for Multijet versions with DPF, the actual interval for changing the oil and replacing the engine oil filter depends on the vehicle usage conditions and is signalled by the warning light or message (if present) in the instrument panel

- Change brake fluid (or every 24 months)

Op. 0010T64 BRAKE AND/OR CLUTCH FLUID CHECK LEVEL AND TOP UP AS NECESSARY

Op. 0010T65 HYDRAULIC BRAKE SYSTEM - BLEED AIR

- Replace the pollen filter (or every 24 months); refer to:

Op. 5010B09 PURIFYING (POLLEN) FILTER FILTER ELEMENT - REPLACE

At the end of the service, connect the Examiner diagnostic equipment to the on board diagnostic socket to zero the mileage counter for the days to the starting value and write the details of the service that has been carried out (date, service no., total mileage) in the Trip Computer memory which can only be read using the diagnostic equipment.

Check that the figure has been set in the instrument panel in km or miles depending on the unit of measurement in that country.

1.2 8v, 1.4 8v

- Check the tyre tread is not worn.

Some types of tyre are fitted with wear gauges; they should be replaced as soon as these gauges are visible on the tread.

Do not swap tyres across.

- Check the tyre inflation pressure is correct. Also check the spare wheel.

The tyre pressures must be checked when they are cold.

- Check that the lighting system is operating correctly: headlamps, turn signals, hazard lights, luggage compartment lights, passenger compartment light and instrument panel warnings lights.

- Check the windscreen wiper system is operating correctly and adjust the sprays if necessary.

- Check the front and rear wiper blades are correctly positioned and not worn.

- Check condition and wear on front disc brake pads and operation of pad wear indicator

- Check rear drum brake linings condition and wear

- Carry out a visual check of: exterior bodywork, underbody protection, rigid and flexible pipes (exhaust - fuel system - braking system) rubber elements (boots - hoses - bushes - etc.)

- Check cleanliness of locks, bonnet and boot lids, cleanliness and lubrication of linkage

- Visually inspect the condition of the accessory drivebelt.

- Check and if necessary adjust the handbrake lever travel; refer to

Op. 3380A04 HANDBRAKE - ADJUST TRAVEL

- Check and, if necessary, adjust tappet clearance; refer to

Op. 1036H14 VALVE TAPPETS - CHECK CLEARANCE

Op. 1036H18 VALVE TAPPETS - ADJUSTMENT FOLLOWING CLEARANCE CHECK

- Check exhaust emissions; refer to

Op. 1080A10 IDLING C.O. LEVEL - CHECK WITH SPECIAL EQUIPMENT

- Replace the air cartridge filter; refer to

Op. 1048A14 AIR CLEANER FILTER ELEMENT - REPLACE.

- Replace the spark plugs; refer to

Op. 5510D10 SPARK PLUGS - R+R

- Restore the brake-clutch fluid level; refer to

Op. 0010T64 BRAKE AND/OR CLUTCH FLUID CHECK LEVEL AND TOP UP AS NECESSARY

- Restore the engine coolant level; refer to

Op. 0010T21 ENGINE COOLANT - CHECK DENSITY AND CHANGE, IF NECESSARY

- Restore the battery fluid, windscreen washer fluid level, etc.

- Check the condition of the timing belt; refer to

Op. 1032D26 TIMING SYSTEM FRONT PROTECTIVE COVER (UPPER PART) - R.R.

- Check the operation of the engine control systems (using the diagnostic socket).

- Change engine oil and oil filter (or every 24 months); refer to

Op. 0010T12 ENGINE OIL AND FILTER - REPLACE

If the vehicle is used mainly around town or the annual km is less than 10,000 km, the engine oil and engine oil filter must be changed every 12 months

- Replace the brake fluid (or every 24 months); refer to:

Op. 0010T64 BRAKE AND/OR CLUTCH FLUID CHECK LEVEL AND TOP UP AS NECESSARY

Op. 0010T65 HYDRAULIC BRAKE SYSTEM - BLEED AIR

- Replace the pollen filter (or every 24 months); refer to:

Op. 5010B09 PURIFYING (POLLEN) FILTER FILTER ELEMENT - REPLACE

At the end of the service, connect the Examiner diagnostic equipment to the on board diagnostic socket to zero the mileage counter for the days to the starting value and write the details of the service that has been carried out (date, service no., total mileage) in the Trip Computer memory which can only be read using the diagnostic equipment.

Check that the figure has been set in the instrument panel in km or miles depending on the unit of measurement in that country.