Passenger airbag disablement warning light flashing
- Make
- Fiat
- Model
- Idea Factory Service Manual
- Year
- 2003–2012
- Section
- Instrument panel › Passenger airbag disablement warning light flashing
‹ Prev Seat belt unfastened warning light onNext › Airbag warning light off / (do not carry out initial test)
Fault diagnosisPassenger airbag disablement warning light flashing
PASSENGER AIRBAG DISABLEMENT WARNING LIGHT FLASHING
The Passenger Air Bag Disabled warning light flashes after the initial four seconds when the ignition is switched on.
| Results of the tests | ||||
| 1 | CHECK WITH DIAGNOSTIC EQUIPMENT | All OK | Problems met | Operation |
|---|---|---|---|---|
| Connect the Examiner diagnostic equipment and check, in the Control Unit Tests, Other Systems, Proxi Alignment Procedure ambients, that the Instrument Panel Node alignment has taken place | Continue to Step 7 | Impossible to carry out the Proxi alignment | Continue to Step 2 | |
| Alignment not carried out | Carry out Proxi alignment | |||
| 2 | CHECK WITH DIAGNOSTIC EQUIPMENT | All OK | Problems met | Operation |
| Connect the Examiner diagnostic equipment and check, in the Instrument Panel Node ambient, that there are no errors and the following parameters are present. | Continue to Step 7 | Impossible to connect with the NQS | Continue to Step 3 | |
| There are errors | Continue to Step 6 | |||
| 3 | ELECTRIC POWER SUPPLY CHECK | All OK | Problems met | Operation |
| Check that the Instrument Panel Node electrical power supply is correct See E4010 INSTRUMENT PANEL | Continue to Step 4 | Positive and/or earth electrical power supply faulty | Replace the defective component (if a fuse is involved, search for the cause of the problem) | |
| 4 | CHECK ELECTRICAL CONNECTIONS | All OK | Problems met | Operation |
| Check the wiring/electrical connections for the Instrument Panel Node, in particular making sure that each individual pin is correctly connected and inserted in its housing. | Continue to Step 5 | Wiring and/or electrical connections not working | Restore the wiring and/or damaged electrical connections | |
| 5 | CHECK WITH DIAGNOSTIC EQUIPMENT | All OK | Problems met | Operation |
| Using the Examiner, check the possibility of connecting with the Instrument Panel Node | Continue to Step 2 | Impossible to connect with the control unit | Replace the instrument panel control unit Op. 5060B11 | |
| 6 | ERRORS CHECK | All OK | Problems met | Operation |
Using the Examiner in the Instrument Panel Node ambient, check that one or more of the following errors is not present:
| Continue to Step 7 | No additional information and/or BUS off detected | Continue according to the instructions for the diagnostic equipment | |
| EEPROM faulty | Replace the instrument panel control unit Op. 5560B11 | |||
| 7 | CHECK WITH ACTIVE DIAGNOSIS | All OK | Problems met | Operation |
| Using the Examiner in the active diagnosis ambient, check that the Autotest function is activated | Continue to Step 8 | The function in question is not controlled by active diagnosis. | Replace the instrument panel control unit Op. 5560B11 | |
| 8 | CHECK WITH DIAGNOSTIC EQUIPMENT | All OK | Problems met | Operation |
| Connect the Examiner diagnostic equipment and check, in the Air Bag Node ambient, that there are no errors and the following parameters are present. | Continue to Step 12 | Impossible to connect with the NAB | Continue to Step 9 | |
| Errors present. | Continue according to the instructions for the diagnostic equipment | |||
| Memory configuration incorrect | Carry out correct configuration | |||
| 9 | ELECTRIC POWER SUPPLY CHECK | All OK | Problems met | Operation |
| Check that the Air Bag Node electrical power supply is correct See E7030 AIRBAG | Continue to Step 10 | Positive and/or earth electrical power supply faulty | Replace the defective component (if a fuse is involved, search for the cause of the problem) | |
| 10 | CHECK ELECTRICAL CONNECTIONS | All OK | Problems met | Operation |
| Check the wiring/electrical connections for the Air Bag Node, in particular making sure that each individual pin is correctly connected and inserted in its housing. | Continue to Step 11 | Wiring and/or electrical connections not working | Restore the wiring and/or damaged electrical connections | |
| 11 | CHECK WITH DIAGNOSTIC EQUIPMENT | All OK | Problems met | Operation |
| Using the Examiner, check the possibility of connecting with the Air Bag Node | Continue to Step 8 | Impossible to connect with the control unit. | Replace the Air Bag control unit Op. 5580C14 | |
| 12 | CHECK ON CORRECT OPERATION | All OK | Problems met | Operation |
| Check that the fault is no longer present | End of diagnosis | Fault persists | Continue to Step 1 | |
‹ Prev Seat belt unfastened warning light onNext › Airbag warning light off / (do not carry out initial test)
Parts & tools for this job For 2003 Fiat Idea
- TOOLOBD2 scanner with SRSSearch: OBD2 scanner ABS SRS
- TOOLTrim removal tool kitSearch: trim removal tool kit
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.