Workshop Manuals Factory service & repair Alfa Romeo
01 General information02 Specifications03 Manufacturing data and tolerances04 Tightening torques05 Fluids and lubricants06 Maintenance07 Diagnostic checks08 Engine09 Clutch10 Gearbox and differential11 Axles and driveshafts12 Brakes13 Steering14 Suspension and wheels15 Heating, air conditioning and auxiliary units16 Electrical equipment17 Body fittings18 Body panels and frame19 Wiring diagrams and electrical functions20 Wiring harnesses21 Connectors and pin-outs22 Fault diagnosis23 Special tools
Alfa Romeo GT Factory Service Manual (2003-2010)22 · Fault diagnosis
22 · Diagnostics

Handbrake applied warning light

Make
Alfa Romeo
Model
GT Factory Service Manual
Year
2003–2010
Section
Instrument panel › Handbrake applied warning light
Fault diagnosisHandbrake applied warning light

HANDBRAKE APPLIED WARNING LIGHT

2.0 JTS, 3.2 V6, 1.9 JTD 16V

The warning light stays on even when the handbrake is off.

A parking brake warning light activation command is sent by the switch on the lever to the Body Computer Node, which makes it available to the Instrument Panel Node via the B-CAN network.

Results of the tests
0PRELIMINARY CHECKSAll OKProblems metOperation
Check that the ABS warning light comes on and goes out properly during the initial testContinue to Step 1The ABS warning light remains on

Continue as instructed

See table

See table K62 ABS AND HANDBRAKE WARNING LIGHTS BOTH ON

1ELECTRICAL EQUIPMENT CHECKAll OKProblems metOperation
Check the earth insulation of the wiring between Parking Brake lever switch and Body Computer.Continue to Step 2Wiring not insulated

Renew the wiring See

See E4010 INSTRUMENT PANEL

2SWITCH CHECKAll OKProblems metOperation
Check the condition of the switch on the parking brake leverContinue to Step 3Faulty switch

Replace switch Op.

Op. 5550D18 HANDBRAKE ON WARNING LIGHT SWITCH - R+R

3CHECK WITH ACTIVE DIAGNOSISAll OKProblems metOperation
With the Examiner in the Instrument Panel Node ambient, check, in active diagnosis, that the handbrake warning light is correctly activatedContinue to Step 6The handbrake warning light does not flash

Replace the instrument panel Op.

Op. 5560B11 ANALOGUE CONTROL PANEL - R+R OR REPLACE

Impossible to connect with the Instrument Panel NodeContinue to Step 4
4CHECK WITH DIAGNOSTIC EQUIPMENTAll OKProblems metOperation
Using the Examiner check, in the Instrument Panel Node ambient, that there are no errors and the following parameters are present.Continue to Step 5There are errorsContinue in accordance with the instructions for the diagnostic equipment
5ELECTRIC POWER SUPPLY CHECKAll OKProblems metOperation
Check that the Instrument Panel Node electrical power supply is correctContinue to Step 3Positive and/or earth electrical power supply faultyReplace the component involved (if a fuse is involved, search for the cause of the problem)
6CHECK ELECTRICAL CONNECTIONSAll OKProblems metOperation
Check the electrical connections between the Body Computer and the Instrument Panel, in particular that each individual pin is correctly connectedContinue to Step 7Electrical connections not workingRestore damaged electrical connections.
7CHECK WITH DIAGNOSTIC EQUIPMENTAll OKProblems metOperation
Using the Examiner, check, in the Body Computer Node ambient, that there are no errors and the specific parameter variesContinue to Step 10Impossible to connect with the Body Computer control unitContinue to Step 8
There are errorsContinue in accordance with the instructions for the diagnostic equipment
The parameter values do not changeContinue to Step 10
8ELECTRIC POWER SUPPLY CHECKAll OKProblems metOperation
Check that the Body Computer Node electrical power supply is correctContinue to Step 9Positive and/or earth electrical power supply faultyReplace the component involved (if a fuse is involved, search for the cause of the problem)
9CHECK WITH DIAGNOSTIC EQUIPMENTAll OKProblems metOperation
Using the Examiner, check the possibility of connecting with the Body Computer NodeContinue to Step 7Impossible to connect with the Body Computer control unit

Replace the Body Computer Op.

Op. 5505A32 BODY COMPUTER - R R

10CHECK ON CORRECT OPERATIONAll OKProblems metOperation
Check that the fault is no longer presentEnd of diagnosisThe fault persists

Replace the Body Computer Op.

Op. 5505A32 BODY COMPUTER - R R

Parts & tools for this job For 2003 Alfa Romeo GT

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.