SLIDING ROOF (ASSEMBLY) - R+R

Operation 7030B12 · SLIDING ROOF

1.2 8v, 1.3 Multijet, 1.4 16v

Removing

- Disconnect the negative battery terminal.

Op. 7030B34 SLIDING ROOF COMPARTMENT DECORATIVE SEAL - R+R

Op. 7065C30 GRAB HANDLE (ONE) LEFT, RIGHT OR CENTRE PASSENGER COMPARTMENT INTERIOR - R.R

- Remove both the sun blinds

Op. 7065C34 SUN BLIND (ONE), LEFT OR RIGHT - R.R.

Op. 7040E10 FRONT COURTESY LIGHT - R+R

Op. 5580M20 ON BOARD NAVIGATION SYSTEM CONTROLS - R.R.

Op. 5570T14 MOBILE PHONE HANDS-FREE SYSTEM MICROPHONE - R R

- Remove both front pillar trims

Op. 7040H30 FRONT PILLAR TRIM (ONE), LEFT OR RIGHT - R.R.

- Remove both centre pillar upper covers.

Op. 7040H38 CENTRE PILLAR UPPER ELEMENT (ONE), LEFT OR RIGHT - R.R

Op. 7040H80 REAR PARCEL SHELF - R.R.

Op. 7040H16 ROOF PANEL LINING FOR VERSIONS WITH SUN ROOF - R.R

Op. 7030B18 SLIDING ROOF GLASS PANEL - R+R

Op. 7030B93 FRONT SLIDING ROOF - R R

1. Disconnect the sunroof electrical connection

- Wear protective gloves and goggles.

- Place suitable protection over the edges and the windscreen to protect the paintwork and the windscreen seal.

1. Cut layer of sealant along the dotted line using an electric cutter with a short blade.

1. Lift the outer edge at the corners and cut the sealant layer using a piano wire.

1. Cut the layer of sealant using an electric cutter with a short blade.

1. Position spacers (1a) to hold sliding roof (1b) up at an angle to allow access with an long blade electric cutter.

2. Working exclusively on the vehicle frame, raise the front edge of the sun roof.

1. Cut the layer of sealant using an electric cutter with a long blade.

1. Remove the sun roof.

Refitting

- Clean the passenger compartment and the parts involved.

- Remove the protection from the paintwork and the windscreen.

- Check that there are no scratches on the paintwork. If necessary, apply a protective anti-rust layer.

- Clean with compressed air jets and degrease the contact surface on the sun roof housing with heptane.

- Extrude a triangular shaped strip of sealant 8 mm long and 14 mm wide max to the triangular profile along the contact surface.

1. Apply the sucker handles suction pads.

2. Lift the roof with the front ceiling panel and clear section and position in its seat, ensuring that it is centred correctly.

3. Place suitable protection on the glass and compress the roof with straps.

- Check that the front glass profile is lowered into the roof panel when the belts are under traction.

1. Secure the electrical connection.

- The vehicle should not be handed back for 24 hours after the bonding of the roof.

Op. 7030B93 FRONT SLIDING ROOF - R R

Op. 7030B18 SLIDING ROOF GLASS PANEL - R+R

Op. 7040H16 ROOF PANEL LINING FOR VERSIONS WITH SUN ROOF - R.R

Op. 7040H80 REAR PARCEL SHELF - R.R.

- Fit both centre pillar upper covers.

Op. 7040H38 CENTRE PILLAR UPPER ELEMENT (ONE), LEFT OR RIGHT - R.R

- Fit both front pillar trims.

Op. 7040H30 FRONT PILLAR TRIM (ONE), LEFT OR RIGHT - R.R.

Op. 5570T14 MOBILE PHONE HANDS-FREE SYSTEM MICROPHONE - R R

Op. 5580M20 ON BOARD NAVIGATION SYSTEM CONTROLS - R.R.

Op. 7040E10 FRONT COURTESY LIGHT - R+R

- Fit both the sun blinds.

Op. 7065C34 SUN BLIND (ONE), LEFT OR RIGHT - R.R.

Op. 7065C30 GRAB HANDLE (ONE) LEFT, RIGHT OR CENTRE PASSENGER COMPARTMENT INTERIOR - R.R

Op. 7030B34 SLIDING ROOF COMPARTMENT DECORATIVE SEAL - R+R

- Connect the negative battery terminal.