ENGINE OIL LEVEL SENSOR - R + R

Operation 1084A40 · INDICATORS/CHECK DEVICES

2.2

Removing

- Position the vehicle on a lift.

- Make sure that the ignition key is in the OFF position, then disconnect the battery terminal (-).

Op. 4450B04 RIGHT FRONT WHEEL - R.R

Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R.

Op. 1020A20 CRANKCASE OIL SUMP - R.R CLEAN SURFACES FOR SEALANT APPLICATION

1. Release the clip.

2. Undo the bolts (2a) and remove the engine oil level sensor (2b).

Refitting

1. Place the engine oil level sensor (1a) in its housing and secure it tightening the bolts (1b) to the recommended torque.

2. Fasten the electrical connection for the engine oil level sensor using the clip.

Op. 1020A20 CRANKCASE OIL SUMP - R.R CLEAN SURFACES FOR SEALANT APPLICATION

Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R.

Op. 4450B04 RIGHT FRONT WHEEL - R.R

- Connect the negative battery terminal.

Op. 0010T11 ENGINE OIL - CHECK LEVEL AND TOP UP, IF NECESSARY

- Remove the vehicle from the lift.

1.9 JTD 8v, 1.9 JTD 16v

Removing

- Position the vehicle on a lift.

- Make sure that the ignition key is in the OFF position, then disconnect the battery terminal (-).

Op. 4450B04 RIGHT FRONT WHEEL - R.R

Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R.

Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.

Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.

Op. 2710A14 RIGHT DRIVESHAFT WITH JOINTS AND INTERMEDIATE DRIVESHAFT - R+R

Op. 1076B72 INTERMEDIATE EXHAUST PIPE WITH HOSE SECTION - R+R

Op. 1048B14 AIR DELIVERY HOSE BETWEEN TURBOCHARGER AND HEAT EXCHANGER - REPLACE

Op. 1084A16 OIL DIPSTICK PIPE - R.R

Op. 1092G10 SINGLE ENGINE BELT - R.R

Op. 1092A10 CRANKSHAFT PULLEY - R + R

Op. 1020A20 CRANKCASE OIL SUMP - R.R CLEAN SURFACES FOR SEALANT APPLICATION

1. Release the clip.

2. Undo the bolts (2a) and remove the engine oil level sensor (2b).

Refitting

1. Place the engine oil level sensor (1a) in its housing and secure it tightening the bolts (1b) to the recommended torque.

2. Fasten the electrical connection for the engine oil level sensor using the clip.

Op. 1020A20 CRANKCASE OIL SUMP - R.R CLEAN SURFACES FOR SEALANT APPLICATION

Op. 1092A10 CRANKSHAFT PULLEY - R + R

Op. 1092G10 SINGLE ENGINE BELT - R.R

Op. 1084A16 OIL DIPSTICK PIPE - R.R

Op. 1048B14 AIR DELIVERY HOSE BETWEEN TURBOCHARGER AND HEAT EXCHANGER - REPLACE

Op. 1076B72 INTERMEDIATE EXHAUST PIPE WITH HOSE SECTION - R+R

Op. 2710A14 RIGHT DRIVESHAFT WITH JOINTS AND INTERMEDIATE DRIVESHAFT - R+R

Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.

Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R.

Op. 4450B04 RIGHT FRONT WHEEL - R.R

Op. 0010T11 ENGINE OIL - CHECK LEVEL AND TOP UP, IF NECESSARY

Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.

- Connect the negative battery terminal.

- Remove the vehicle from the lift.

2.4 JTD 20v

Removing

Op. 4450B12 FRONT WHEELS (TWO) - R+R

Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R.

Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.

Op. 7055B90 LEFT FRONT WHEEL ARCH LINER - R.R.

Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.

Op. 2710A14 RIGHT HAND DRIVE SHAFT WITH JOINTS - R+R

Op. 1076B72 INTERMEDIATE EXHAUST PIPE WITH HOSE SECTION - R+R

Op. 1048B14 AIR DELIVERY HOSE BETWEEN TURBOCHARGER AND HEAT EXCHANGER - REPLACE

Op. 1084A16 OIL DIPSTICK PIPE - R.R

Op. 1092G10 SINGLE ENGINE BELT - R.R

Op. 1092A10 CRANKSHAFT PULLEY - R + R

Op. 1076B18 RIGID SECTION OF EXHAUST PIPE BETWEEN CATALYTIC CONVERTER AND SILENCER - R + R

Op. 7055A43 CENTRE FRONT GRILLE - R.R.

Op. 4410D10 FRONT SUSPENSION FRAME - R+R

Op. 1020A20 CRANKCASE OIL SUMP - R.R CLEAN SURFACES FOR SEALANT APPLICATION

- Undo the bolts and remove the engine oil level sensor.

Refitting

- Fit the engine oil level sensor in place and secure it using the bolts.

Op. 1020A20 CRANKCASE OIL SUMP - R.R CLEAN SURFACES FOR SEALANT APPLICATION

Op. 4410D10 FRONT SUSPENSION FRAME - R+R

Op. 7055A43 CENTRE FRONT GRILLE - R.R.

Op. 1076B18 RIGID SECTION OF EXHAUST PIPE BETWEEN CATALYTIC CONVERTER AND SILENCER - R + R

Op. 1092A10 CRANKSHAFT PULLEY - R + R

Op. 1092G10 SINGLE ENGINE BELT - R.R

Op. 1084A16 OIL DIPSTICK PIPE - R.R

Op. 1048B14 AIR DELIVERY HOSE BETWEEN TURBOCHARGER AND HEAT EXCHANGER - REPLACE

Op. 1076B72 INTERMEDIATE EXHAUST PIPE WITH HOSE SECTION - R+R

Op. 2710A14 RIGHT HAND DRIVE SHAFT WITH JOINTS - R+R

Op. 7055B90 LEFT FRONT WHEEL ARCH LINER - R.R.

Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.

Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R.

Op. 4450B12 FRONT WHEELS (TWO) - R+R

Op. 0010T11 ENGINE OIL - CHECK LEVEL AND TOP UP, IF NECESSARY

Op. 4450A10 FRONT WHEEL GEOMETRY - CHECK USING OPTICAL EQUIPMENT - INCLUDES ADJUSTMENT IF NECESSARY

Op. 7055B54 UNDER ENGINE PROTECTION/GUARD - R.R.

1.8

Removing

Op. 1076B18 RIGID SECTION OF EXHAUST PIPE BETWEEN CATALYTIC CONVERTER AND SILENCER - R + R

Op. 0010T11 ENGINE OIL - CHECK LEVEL AND TOP UP, IF NECESSARY

Op. 1084A16 OIL DIPSTICK PIPE - R.R

Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R.

Op. 1020A20 CRANKCASE OIL SUMP - R.R CLEAN SURFACES FOR SEALANT APPLICATION

Op. 1020A46 CRANKCASE OIL SUMP PARTITION - R.R. WITH CRANKCASE SUMP REMOVED

1. Remove the retaining ring.

2. Undo the bolts (2a) and remove the engine oil level sensor (2b).

Refitting

- Place the engine oil level sensor in its housing and tighten the bolts to the recommended torque.

- Fasten the electrical connection for the engine oil level sensor using the safety clip.

Op. 1020A46 CRANKCASE OIL SUMP PARTITION - R.R. WITH CRANKCASE SUMP REMOVED

Op. 1020A20 CRANKCASE OIL SUMP - R.R CLEAN SURFACES FOR SEALANT APPLICATION

Op. 7055B66 ENGINE COMPARTMENT DUST COVER IN RIGHT FRONT WHEEL ARCH - R.R.

Op. 1084A16 OIL DIPSTICK PIPE - R.R

Op. 1076B18 RIGID SECTION OF EXHAUST PIPE BETWEEN CATALYTIC CONVERTER AND SILENCER - R + R

Op. 0010T11 ENGINE OIL - CHECK LEVEL AND TOP UP, IF NECESSARY