Workshop Manuals Factory service & repair Fiat
01 General information02 Specifications03 Manufacturing data and tolerances04 Tightening torques05 Fluids and lubricants06 Maintenance07 Diagnostic checks08 Engine09 Clutch10 Gearbox and differential11 Axles and driveshafts12 Brakes13 Steering14 Suspension and wheels15 Heating, air conditioning and auxiliary units16 Electrical equipment17 Body fittings18 Body panels and frame19 Wiring diagrams and electrical functions20 Wiring harnesses21 Connectors and pin-outs22 Fault diagnosis23 Special tools
Fiat Stilo Factory Service Manual (2001-2007)08 · Engine
08 · Engine

Throttle case - r + r

Make
Fiat
Model
Stilo Factory Service Manual
Year
2001–2007
Section
Petrol injection system › Throttle case - r + r
EngineThrottle case - r + r

Throttle case - r + r

Operation 1056B14 · Multi-point injection system (mpi)

1.8 16v

Removing

- 5530B56 BATTERY DRIP TRAY COVER - R.R.

Disconnect the battery negative terminal.

- 1048A28 vacuum air circuit resonator pipe - r+r

1. Disconnect electrical connections (1a) and (1b) from the throttle body.

NameConnector
1aIntegrated throttle body actuatorN75
NameConnector
1bIntegrated throttle body actuatorN75

2. Disconnect throttle casing pipe.

Throttle case - r + r

2.4 20v

Removing

- 1016A40 ignition coil cover on cylinder head- r+r.

- 5530B56 BATTERY DRIP TRAY COVER - R.R.

Disconnect the battery negative terminal.

- 5530B52 Battery DRIP TRAY/SUPPORT - R.R.

- 1056B82 injection/ignition system e.c.u. (one) - r + r

- 1048A31 RIGID PIPE between air filter and intake manifold - R.R..

1. Disconnect the electrical connection for the integrated throttle body actuator.

NameConnector
1Integrated throttle body actuatorN75

2. Undo the (2a) and disconnect the control unit earth lead (2b).

3. Undo the bolts (3a) and remove the throttle casing (3b) complete with control unit mounting and gasket (3c).

Throttle case - r + r

1.8 16v

1. Undo the retaining bolts (1a) and remove the throttle casing (1b).

Throttle case - r + r

2.4 20v

Refitting

Proceed with the refitting as described below.

If the throttle casing is being replaced, the control unit learning procedure must be carried out at the end of the refitting procedure; 1056B14 throttle case - r + r

Connect the control unit earth lead and tighten the fixing bolt.

- 1048A31 RIGID PIPE between air filter and intake manifold - R.R..

- 1056B82 injection/ignition system e.c.u. (one) - r + r

- 5530B52 Battery DRIP TRAY/SUPPORT - R.R.

Connect the battery negative terminal lead.

- 5530B56 BATTERY DRIP TRAY COVER - R.R.

- 1016A40 ignition coil cover on cylinder head- r+r.

1.8 16v

Refitting

Fit the throttle casing into the seat on the modular intake manifold.

Tighten the bolts retaining the throttle casing to the intake manifold.

Connect the throttle casing coolant pipe and the engine oil vapour pipe.

Connect the electrical connections disconnected previously.

- 1048A28 vacuum air circuit resonator pipe - r+r

Connect the battery negative terminal.

- 5530B56 BATTERY DRIP TRAY COVER - R.R.

Parts & tools for this job For 2001 Fiat Stilo

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.