Cam angle sensor r + r

Operation 1056B51 · Multi-point injection system (mpi)

1.2 16v

Removing

- 5530B56 BATTERY DRIP TRAY COVER - R.R..

Disconnect the battery negative terminal.

- 1048A10 air cleaner filtering element - replace

1. Disconnect the electrical connection for the cam angle sensor.

2. Undo the fixing bolt (2a) and remove the cam angle sensor (2b).

1.4 16v

Removing

- 5530B56 BATTERY DRIP TRAY COVER - R.R.

Disconnect the battery negative terminal.

- 1048A10 air cleaner filtering element - replace

1. Disconnect the electrical connector for the sensor retracting the retaining clip located underneath the actual connector.

2. Undo the fixing bolt (2a) and remove the sensor (2b).

1.8 16v

Removing

- 5530B56 BATTERY DRIP TRAY COVER - R.R.

Disconnect the battery negative terminal.

Place the car on a ramp.

- 1016A40 ignition coil cover on cylinder head- r+r

- 5530B56 BATTERY DRIP TRAY COVER - R.R.

- 1048A28 vacuum air circuit resonator pipe - r+r

- 1048A32 sleeve from air cleaner to intake manifold - r + r

- 1048A23 cold air intake - r r

- 4450B10 Front WHEEL (one) - R.R.

- 7055B54 under-engine guard - r r

- 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R.

- 1088B10 engine cooling tank - r + r

- 5510C14 ignition coil/s - r+r

- 1016A20 single cam cover - r + r and replace gasket

- 1008A46 cam shaft left rigid mount - r r

- 1032D12 timing system protective cover(s) - r + r

- 1032B14 toothed timing belt - r + r for timing adjustment or replacement versions with air conditioner

- 1032B40 toothed-driven pulley (one) - r + r with timing belt removed

- 1032B53 driven toothed pulley (one) - r r for versions with air conditioner

1. Undo the bolts (1a) and remove the cam angle sensor (1b).

1.2 16v

Refitting

Fit the cam angle sensor and tighten the retaining bolt.

Connect the electrical connector for the cam angle sensor.

- 1048A10 air cleaner filtering element - replace

Connect the battery negative terminal.

- 5530B56 BATTERY DRIP TRAY COVER - R.R..

1.4 16v

Refitting

Fit the sensor and tighten the fixing bolt.

Connect the electrical connector for the sender unit.

- 1048A10 air cleaner filtering element - replace

Connect the battery negative terminal.

- 5530B56 BATTERY DRIP TRAY COVER - R.R.

1.8 16v

Refitting

Fit the cam angle sensor and fix it using the bolts.

- 1032B53 driven toothed pulley (one) - r r for versions with air conditioner

- 1032B40 toothed-driven pulley (one) - r + r with timing belt removed

- 1032B14 toothed timing belt - r + r for timing adjustment or replacement versions with air conditioner

- 1032D12 timing system protective cover(s) - r + r

- 1008A46 cam shaft left rigid mount - r r

- 1016A20 single cam cover - r + r and replace gasket

- 5510C14 ignition coil/s - r+r

- 1088B10 engine cooling tank - r + r

- 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R.

- 7055B54 under-engine guard - r r

- 4450B10 Front WHEEL (one) - R.R.

- 1048A23 cold air intake - r r

- 1048A32 sleeve from air cleaner to intake manifold - r + r

- 1048A28 vacuum air circuit resonator pipe - r+r

- 5530B56 BATTERY DRIP TRAY COVER - R.R.

- 1016A40 ignition coil cover on cylinder head- r+r

- 0010T21 coolant check density and top up if necessary

Remove the vehicle from the ramp.

Connect the battery negative terminal.

- 5530B56 BATTERY DRIP TRAY COVER - R.R.