Workshop Manuals Factory service & repair Nissan and Datsun
01 Nissan-S110 S12 S13 S14 S15 Silvia 200SX 240SX02 INDEX03 GI - General Information04 MA - Maintenance05 EM - Engine Mechanical06 LC - Engine Lubrication & Cooling07 EF&EC - Fuel & Emission Control08 FE - Engine Control, Fuel & Exaust09 CL - Clutch10 MT - Manual Transmission11 AT - Automatic Transmission12 PD - Propeller Shaft & Differential13 FA - Front Axle & Suspension14 RA - Rear Axle & Suspension15 BR - Brake System16 ST - Steering System17 BF - Body18 HA - Heater & Air Conditioner19 EL - Electrical System20 Inch/Metric Converion Tables21 Quick Reference Chart
Nissan and Datsun Nissan 200SX S12 1986 Workshop Manual11 · AT - Automatic Transmission
11 · Transmission

“TROUBLE-SHOOTING AND DIAGNOSES - Nissan 200SX S12 Workshop Manual

Make
Nissan and Datsun
Model
200SX Nissan 200SX S12 1986 Workshop Manual
Section
General › “TROUBLE-SHOOTING AND DIAGNOSES - Nissan 200SX S12 Workshop Manual
AT - Automatic Transmission“TROUBLE-SHOOTING AND DIAGNOSES - Nissan 200SX S12 Workshop Manual

“TROUBLE-SHOOTING AND DIAGNOSES

“TROUBLE-SHOOTING AND DIAGNOSES

Pressure Testing (Cont'd) 1) When line pressure is low at all positions, the Atidling problem may be due to: ‘CAZ0E engine Wear on interior of oil pump Oil leakage at or around cil pump, control valve body, transmission case or gavernor Sticking pressure regulator valve Sticking pressure modifier valve When line pressure is low at a particular pos!- tion, the problem may be due to thé following: Hf oll leaks at or around forward clutch (rear) or governor, line pressure is low in “D”, "2" or "4" range but is normal in ”R” range. At stall test 1f ofl leaks at or around low and raverse brake 1, Start engine and place select lever in “D" circuit, line pressure becomes tow in ‘’R" or ange. “Pp” range but is normal in “D", “2 or “1”

RangeLine pressure kPa (ko/om?, psi}
R412 - 649 (4.2 - 6.6, 60-80)
D314-373 (82-38, 40-64)
2888 - 1,147 {6.0 11.7, 85- 166)
1314-373 (3.2-3.8, 46 -54)

2. Apply foot brake and accelerate to wide-open range. throttle. 3 When line pressure is high, pressure regulator

3. Quickly note the line pressure and immediately valve may have stuck. release throttle, 4, Shift select lever to “N”.

5. Cool off A.T.F.

6. Perform jine pressure testing in the same man- ner as in steps 2 through 6 with select lever in “2”, "1" and “R", respectively. © Do not perform tests for more than five seconds at any shift range, * Do not proceed to next “range” test imme ately after one “range” test is done. Wait until oil temperature decreases,

CA20E engine

RangeLime pressure kPa (kg/cm? psi)
R402 - 1,589 (14.3 - 16.2, 203 - 230)
D971 - 1,080 (9.9- 11.1, 141 - 158)
2991 - 1,138 {10.1- 17.6, 144 165)
1971 - 1,089 (9.9- 91.1, 149 158)

Judgment by measuring line pressure If line pressure does not risa, first check to meke sure that vacuum hosa is connected properly.

AT-74

Parts & tools for this job For Nissan 200SX

As an Amazon Associate we earn from qualifying purchases.