E.g.r. system solenoid - r + r
- Make
- Fiat
- Model
- Bravo Factory Service Manual
- Year
- 2007–2014
- Section
- Emission control system › E.g.r. system solenoid - r + r
E.G.R. SYSTEM SOLENOID - R + R
Removing
Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R
Op. 1048B27 RIGID PIPE FOR AIR INLET TO THROTTLE BODY - R R
Op. 1060G50 THROTTLE BODY - R.R
1. Loosen the collar (1a) and disconnect the exhaust gas outlet hose from the exhaust gas/water heat exchanger for the E.G.R. system (1b), heat exchanger side.
2. Disconnect the electrical connection for the E.G.R. system solenoid valve.
| Description | Connector | |
|---|---|---|
| 2 | EGR solenoid valve | See L030 EGR SOLENOID VALVE |
3. Undo the bolts (3a) and remove the E.G.R. system solenoid valve (3b) complete with hose.
Refitting
- Place the gasket back in its housing.
- Place the E.G.R. system solenoid valve in its housing complete with hose and fasten it tightening the bolts to the recommended torque.
| Component | Fastening | dia | Value (daNm) | Validity |
|---|---|---|---|---|
| E.G.R. system solenoid | Bolt | M8 | 2.3 ÷ 2.8 | 1.9 JTD |
- Connect the electrical connection for the E.G.R. solenoid valve.
- Connect the exhaust gas outlet hose from the exhaust gas/water heat exchanger for the E.G.R. system, heat exchanger side and tighten the collar.
Op. 1060G50 THROTTLE BODY - R.R
Op. 1048B27 RIGID PIPE FOR AIR INLET TO THROTTLE BODY - R R
Op. 5530B52 BATTERY SUPPORT/DRIP TRAY - R.R
Removing
Op. 1016A10 SOUND-PROOFING COVER - R.R
- Undo the nut fixing the water pipe retaining bracket to the heater and move it to one side.
1. Undo the bolts fixing the exhaust gas outlet from the water/exhaust gas heat exchanger for the E.G.R. system.
2. Disconnect the electrical connection from the EGR system solenoid valve
| Description | Connector | |
|---|---|---|
| 2 | EGR solenoid valve | See L030 EGR SOLENOID VALVE |
3. Undo the bolts fixing the E.G.R. system solenoid valve.
4. Remove the E.G.R. system solenoid valve.
- Remove the gasket.
Refitting
- Place the E.G.R. system solenoid valve in its housing complete with new gasket and tighten the bolts to the recommended torque.
| Component | Fastening | dia | Value (daNm) | Validity |
|---|---|---|---|---|
| E.G.R. system solenoid | Bolt | M8 | 2.3 ÷ 2.8 | 1.9 JTD |
- Connect the electrical connection from the EGR system solenoid valve
- Tighten the bolts fixing the exhaust gas outlet to the water/exhaust gas heat exchanger for the E.G.R. system.
- Refit the water pipe bracket complete and tighten the nut.
Parts & tools for this job For 2007 Fiat Bravo
- PARTExhaust gasketSearch: Fiat Bravo 2007 exhaust gasket
- TOOLPenetrating oilSearch: penetrating oil
- TOOLOBD2 scannerSearch: OBD2 scanner
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.