Check engine control unit connections
- Make
- Fiat
- Model
- Croma Factory Service Manual
- Year
- 2005–2010
- Section
- Diesel injection system › Check engine control unit connections
CHECK ENGINE CONTROL UNIT CONNECTIONS
| STEP | CHECK TO BE PERFORMED | RESOLUTION IF THE CHECK IS NOT OK |
|---|---|---|
| 1 | Turn the ignition key OFF. connect the cable loom connector to the accelerator pedal potentiometer Turn the ignition key ON. Select the following system on the diagnostic equipment: Diesel EDC16C39 electronic injection system. Check that error P0641 – Power supply to sensors 1 is “Present”. Move on to Step 5 | Move on to Step 2 |
| 2 | Turn the ignition key OFF. Disconnect the wiring harness connector from engine control unit connector A Turn the ignition key ON. Check that the voltage between pin 9 of the control unit See M010 ENGINE MANAGEMENT CONTROL UNIT and the earth is greater than 0.3 V. | Repair or if necessary replace the electrical wiring between the accelerator pedal potentiometer and the engine control unit |
| 3 | Check that the voltage between pin 30 of the control unit See M010 ENGINE MANAGEMENT CONTROL UNIT and the earth is greater than 0.3 V. | Repair or if necessary replace the electrical wiring between the accelerator pedal potentiometer and the engine control unit |
| 4 | Replace the accelerator pedal Op. 1068A20 ACCELERATOR PEDAL WITH BUILT-IN POTENTIOMETER - R.R and check the fault has disappeared. The test can be considered over | Repair the original accelerator pedal and replace the engine management control unit. |
| 5 | Turn the ignition key OFF. Disconnect the cable loom connector from the timing sensor. Turn the ignition key ON. Select the following system on the diagnostic equipment: Diesel EDC16C39 electronic injection system. Check that error P0641 – Power supply to sensors 1 is “Present”. | Replace the timing sensor Op. 5510C30 ENGINE TIMING SENSOR - R+R |
| 6 | Turn the ignition key OFF. Disconnect the wiring harness connector from engine control unit connector A Turn the ignition key ON. Check that the voltage between pin 45 of the control unit See M010 ENGINE MANAGEMENT CONTROL UNIT and the earth is greater than 0.3 V. Move on to Step 8 | Move on to Step 7 |
| 7 | If faults are present, repair or if necessary replace the electrical wiring between the engine control unit and the accelerator pedal potentiometer. See E5050 DIESEL ENGINES ELECTRONIC MANAGEMENT Replace the wiring if necessary The test can be considered over | Replace the accelerator pedal Op. 1068A20 ACCELERATOR PEDAL WITH BUILT-IN POTENTIOMETER - R.R |
| 8 | Turn the ignition key OFF. Check that the voltage between pin 30 of the control unit See M010 ENGINE MANAGEMENT CONTROL UNIT and the earth is more than 500 kOhm. | Repair or if necessary replace the electrical wiring between the accelerator pedal potentiometer and the engine control unit |
| 9 | Disconnect the cable loom connector from engine management control unit connector B Turn the ignition key ON. Check that the voltage between pin 11 of the control unit See M010 ENGINE MANAGEMENT CONTROL UNIT and the earth is greater than 0.3 V. | Repair or if necessary replace the electrical wiring between the timing sensor and the engine control unit |
| 10 | Turn the ignition key OFF. Check that the voltage between pin 11 of the control unit See M010 ENGINE MANAGEMENT CONTROL UNIT and the earth is more than 500 kOhm. | Repair or if necessary replace the electrical wiring between the timing sensor and the engine control unit |
| 11 | Replace the engine management control unit |
Parts & tools for this job For 2005 Fiat Croma
- PARTEngine gasket setSearch: Fiat Croma 2005 engine gasket set
- TOOLTorque wrenchSearch: 3/8 inch torque wrench
- TOOLFeeler gauge setSearch: feeler gauge set
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.