Rh cylinder head extension - replace gasket
- Make
- Fiat
- Model
- Stilo Factory Service Manual
- Year
- 2001–2007
- Section
- Cylinder head/s › Rh cylinder head extension - replace gasket
Rh cylinder head extension - replace gasket
Removing
Place the vehicle on a ramp.
- 1016A10 sound-proofing cover - r + r
- 5530B56 BATTERY DRIP TRAY COVER - R.R.
Disconnect the battery negative terminal.
| Name | Connector | |
|---|---|---|
| Battery | A1 |
- 7055B54 under-engine guard - r r
- 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R.
- 4450B10 Front WHEEL (one) - R.R.
- 1092B50 alternator/air conditioner compressor drive belt - adjust tension
- 1008B10 power unit front mount (timing side) flexible block - replace
- 1008A46 cam shaft left rigid mount - r r
- 1032D12 timing system protective cover(s) - r + r
- 1092A10 Crankshaft services PULLEY - R.R.
- 1056B82 injection/ignition system e.c.u. (one) - r + r
- 1056B87 ignition/injection system control unit mount - r r
- 1036G49 rear camshaft seal, lh or rh - r r with mount and coil/s removed
- 1032B10 toothed timing belt - r + r for timing adjustment or replacement
- 1048A32 sleeve from air cleaner to intake manifold - r + r
- 1056B15 throttle body intergral with mds - r r
- 1084A16 oil dip stick pipe - r r
- 1084A22 engine oil filler - r r
- 1072B50 sleeves connecting air capacity box to inlet manifold is - r+r
- 1032B40 toothed-driven pulley (one) - r + r with timing belt removed
- 1080B94 front lambda probe with catalitic converter r r
- 1072C44 exhaust manifold heat shield on bulkhead - r+r
- 1016B26 rh cylinder head extension -r r with timing belt removed -replace gasket
Refitting
- 1016B26 rh cylinder head extension -r r with timing belt removed -replace gasket
- 1072C44 exhaust manifold heat shield on bulkhead - r+r
- 1080B94 front lambda probe with catalitic converter r r
- 1032B40 toothed-driven pulley (one) - r + r with timing belt removed
- 1072B50 sleeves connecting air capacity box to inlet manifold is - r+r
- 1084A22 engine oil filler - r r
- 1084A16 oil dip stick pipe - r r
- 1056B15 throttle body intergral with mds - r r
- 1048A32 sleeve from air cleaner to intake manifold - r + r
- 1032B10 toothed timing belt - r + r for timing adjustment or replacement
- 1036G49 rear camshaft seal, lh or rh - r r with mount and coil/s removed
- 1056B87 ignition/injection system control unit mount - r r
- 1056B82 injection/ignition system e.c.u. (one) - r + r
- 1092A10 Crankshaft services PULLEY - R.R.
- 1032D12 timing system protective cover(s) - r + r
- 1008A46 cam shaft left rigid mount - r r
- 1008B10 power unit front mount (timing side) flexible block - replace
- 1092B50 alternator/air conditioner compressor drive belt - adjust tension
- 1092B54 alternator/water pump drive belt - adjust tension
- 4450B10 Front WHEEL (one) - R.R.
- 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R.
- 7055B54 under-engine guard - r r
Connect the battery's negative terminal.
| Name | Connector | |
|---|---|---|
| Battery | A1 |
- 5530B56 BATTERY DRIP TRAY COVER - R.R.
- 1016A10 sound-proofing cover - r + r
Remove the car from the ramp.
Parts & tools for this job For 2001 Fiat Stilo
- PARTEngine gasket setSearch: Fiat Stilo 2001 engine gasket set
- TOOLTorque wrenchSearch: 3/8 inch torque wrench
- TOOLFeeler gauge setSearch: feeler gauge set
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.