Freelander Service Procedures
TORQUE WRENCH SETTINGS
06-6
Engine – KV6
TORQUE DESCRIPTION
METRIC
IMPERIAL
Bearing ladder to cylinder block bolts
†
⇒
Stage 1
20 Nm
15 lbf.ft
⇒
Stage 2
+90
°
+90
°
Camshaft carrier to cylinder head bolts
†++
10 Nm
7.5 lbf.ft
Camshaft cover to carrier bolts
†
9 Nm
7 lbf.ft
Camshaft timing belt cover bolts
4 Nm
3 lbf.ft
Camshaft timing belt front cover backplate to cylinder head bolts
+
9 Nm
7 lbf.ft
Camshaft timing belt rear cover backplate to cylinder head bolts
+
9 Nm
7 lbf.ft
Camshaft timing belt tensioner bolts
25 Nm
18 lbf.ft
Camshaft timing gear bolts *
⇒
Stage 1
27 Nm
20 lbf.ft
⇒
Stage 2
+90
°
+90
°
Camshaft position sensor bracket to camshaft cover bolt
9 Nm
7 lbf.ft
Connecting rod big-end bolts
⇒
Stage 1
20 Nm
15 lbf.ft
⇒
Stage 2
+45
°
+45
°
Crankcase (lower) to cylinder block bolts
⇒
M6 bolts
+++
25 Nm
7 lbf.ft
⇒
M8 bolts
+++
25 Nm
18 lbf.ft
Crankshaft pulley bolt
160 Nm
118 lbf.ft
Crankshaft rear oil seal to cylinder block bolts
* †
8
Nm
6
lbf.ft
Cylinder head bolts
†
⇒
Stage 1
25 Nm
18 lbf.ft
⇒
Stage 2
18 lbf.ft
18 lbf.ft
⇒
Stage 3
25 Nm
18 lbf.ft
⇒
Stage 4
+180
°
+180
°
Drain plug to sump
25 Nm
18 lbf.ft
Drive plate to crankshaft bolts
†
⇒
Stage 1
⇒
Stage 2
25 Nm
100 Nm
18 lbf.ft
74 lbf.ft
Earth lead to RH camshaft cover bolt
9 Nm
7 lbf.ft
Engine front mounting plate to cylinder block and IRD bracket
⇒
M10 bolt - No. 1 on tightening sequence
25 Nm
18 lbf.ft
⇒
M10 bolt - No. 5 on tightening sequence
45 Nm
33 lbf.ft
⇒
M12 bolts
85 Nm
63 lbf.ft
Engine mounting bracket to engine front plate bolts
45 Nm
33 lbf.ft
Engine mounting (LH) to body bolts
45 Nm
33 lbf.ft
Engine mounting bracket (LH) to gearbox bracket through bolt
85 Nm
63 lbf.ft
Engine mounting bracket (LH) to gearbox bracket through bolt
100 Nm
74 lbf.ft
Engine steady (lower) to sump bracket and subframe bolts
100 Nm
74 lbf.ft
Engine steady (upper RH) to body bolts
100 Nm
74 lbf.ft
Engine steady (upper RH) to top arm bolt
100 Nm
74 lbf.ft
Fuel rail to inlet manifold bolts
9 Nm
7 lbf.ft
Heat shield (RH rear timing belt) to cylinder head bolts
⇒
M6
9 Nm
7 lbf.ft
⇒
M8
25 Nm
18 lbf.ft
Hydramount (RH)
85 Nm
63 lbf.ft
Idler pulley to engine front mounting plate Allen bolt
45 Nm
33 lbf.ft