Octavia Mk1: Electrical System
Also for this vehicle: Octavia Mk2.
Steering & suspension
Electrical
Body & interior
Heating & A/C
Engine
Transmission
General
Choose Sections to see everything in a chapter, or a chapter title to start at its first page.
Electrical System292 pages
Starter-current supply-CC21 pages
Battery11 pages
- Battery handling instructions
- Inspecting electrolyte level
- Measuring voltage under load
- Basics
- Work sequence when disconnecting and connecting the battery
- Check the battery
- Measure no-load voltage
- Measuring voltage under load
- Charging batteries
- Removing and installing the battery
- Removing and installing the battery tray
Battery with a magic eye and battery plugs covered in adhesive tape2 pages
Battery with a magic eye without battery plugs covered in adhesive tape (maintenance-free)2 pages
Removing and installing the AC generator5 pages
- Removing and installing the starter
Instruments, GCI59 pages
Dash panel insert (? MY 00)22 pages
- Self-diagnosis
- Initiating self-diagnosis of the dash panel insert
- Interrogating fault memory
- Fault table
- Actuator diagnosis
- Erasing fault memory
- Ending output
- Coding control unit
- Reading measured value block
- Adjustment
- Adapt service interval display - SID
- Input values when changing the dash panel insert
- Resetting service interval display (SID) without V.A.G 1552 / V.A.G 1551
- Resetting service interval display (SID) with V.A.G 1552 / V.A.G 1551
- Removing and installing the dash panel insert
- Lamp assignment on the dash panel insert
- Contact assignment of plug connections on the dash panel insert
- Test signal from fuel gauge sender G
- Contact assignment on the fuel gauge sender G
- Check coolant temperature sender
- Testing the speed signal
Taximeter and printer3 pages
Dash panel insert (MY 01 ?)13 pages
- Self-diagnosis
- Initiating self-diagnosis of the dash panel insert
- Interrogating fault memory
- Fault table
- Actuator diagnosis
- Erasing fault memory
- Ending output
- Coding dash panel insert
- Reading measured value block
- Adaptation
- Adapting the service interval display when replacing the dash panel insert
- Input values when changing the dash panel insert
Self-diagnosis of the Gateway16 pages
- Initiating self-diagnosis
- Interrogating fault memory
- Fault table
- Erasing fault memory
- Ending output
- Coding control unit
- Reading measured value block
- Removing and installing the dash panel insert
- Contact assignment of plug connections on the dash panel insert
- Test signal from fuel gauge sender G
- Contact assignment on the fuel gauge sender G
- Check coolant temperature sender
- Testing the speed signal
- Outside temperature sensor G17
- Check oil level and oil temperature sender G266
Infotainment52 pages
- Removing and installing the roof aerial
- Removing and installing roof aerial for radio as of MY 2002
- Removing and installing roof aerial for radio and telephone as of MY 2002
- Removing and installing roof aerial for radio, telephone and navigation system as of MY 2002
- Removing and installing the control unit for the mobile phone operating electronics J412 (interface box)
- Overview of the mount for the mobile phone 1
- Overview of the mount for the mobile phone 2
- Removing and installing the microphone for the telephone R38 ? 08.00
- Removing and installing the microphone for the telephone R38 09.00 ?
Self-diagnosis of radio system "Gamma (MS 501), MS 303 and Symphony”7 pages
- Removing and installing CD changer
Navigation system13 pages
- General description
- Self-diagnosis of radio unit in RNS
- Self-diagnosis of navigation unit in RNS
- Interrogating and erasing fault memory
- Fault table
- Actuator diagnosis
- Reading measured value block
- Adaptation
- Code control unit for RNS
- Electronic anti-theft lock
- Plug connections at Radio-Navigation System
- Removing and installing Radio-Navigation System
Multi-functional steering wheel9 pages
- General description
- Interrogating and erasing fault memory
- Fault table
- Coding multi-functional steering wheel control unit J453
- Actuator diagnosis
- Reading measured value block
- Removing and installing the key units of the multi-function steering wheel
- Contact assignment of the 18-pin plug connection for the CU multi-functional steering wheel J453
Windscreen wipe/wash system20 pages
Windscreen wiper and washer system3 pages
Repairing windscreen washer system4 pages
Repairing headlamp cleaning system4 pages
Rear window wiper and washer system9 pages
Lights, lamps, switches outside70 pages
- Removing and installing the licence plate illumination
Repairing lock cylinder and ignition starter switch4 pages
- Removing and installing rear lights Octavia Combi
Additional brake light3 pages
Self diagnosis for the Xenon headlights with automatic regulation (System Litronic 4.1)9 pages
Xenon headlights with automatic regulation (System Litronic 4.1) - overall view13 pages
- Headlight with control unit
- Removing and installing front Xenon headlights
- Changing light bulbs in the headlight
- Removing and installing the D2S discharge lamp
- Removing and installing the ignition/high voltage unit BOSCH 2.3
- Removing and installing stepper motor
- Removing and installing front sender
- Removing and installing rear sender
- Removing and installing control unit
- Possibilities of sender adjustment
- Connection identification of the Xenon headlamps
- Switch over the inner aperture in the Xenon headlight
Lights, lamps, switches inside, anti-theft system64 pages
Diagnosis of the electronic immobiliser23 pages
- Self-diagnosis of the 1st generation immobiliser
- Initiating self-diagnosis
- Interrogating control unit version
- Interrogating fault memory
- Fault table
- Erasing fault memory
- Ending output
- Reading measured value block
- Adaptation
- Adapt ignition key
- Adaptation after changing the engine control unit
- Adaptation after changing the immobiliser control unit
- Transponder defective and/or key loss
- Replacing reader coil
Procedure when changing the lock set or the immobiliser control unit3 pages
- System check
Repairing switch8 pages
- Removing and installing switches in centre console
- Removing and installing light switch
- Removing and installing the headlight range control adjuster
- Removing and installing the door contact switch
- Removing and installing electrical switch for sun roof and interior light
- Removing and installing the mirror adjustment switch
- Removing and installing the switch for the power window lifter
Repairing interior lights7 pages
- Removing and installing luggage compartment light
- Removing and installing switch for remote release/fuel tank cap
- Removing and installing the luggage compartment power socket
Sensor for interior monitoring G2734 pages
- Self-diagnosis of the 2nd generation immobiliser MY 01 ?
Self-diagnosis of the 3rd generation immobiliser MY 01 ?14 pages
- Carry out self-diagnosis of immobiliser
- Interrogating fault memory
- Fault table
- Erasing fault memory
- Ending output
- Reading measured value block
- Performing the log-in procedure
- Adapt ignition key
- Adaptation after changing the new engine control unit
- Adaptation after insertion of a used engine control unit
- Adaptation after changing the new immobiliser control unit
Wiring6 pages
Relay holder, fuse holder3 pages
Major electrical assignments and major plug connections3 pages