Workshop Manuals Factory service & repair Nissan and Datsun
01 cover02 A (intro)03 B (CA18DET/ECCS)04 C (driveline)05 D (body & frame)06 E (interior electric)07 F (misc. codes)08 manual notes09 Front cover10 CONTENTS11 GI General information12 MA maintenance13 EM engine mechanical14 LC lubrication & cooling15 EF &EC engine fuel & emission control system16 FE engine control fuel & exhaust systems17 CL clutch18 MT manual transmission19 AT automatic transmission20 PD prop shaft & diff carrier21 FA front axle & suspension22 RA rear axle & suspension23 BR brake system24 ST steering25 BF body26 HA heater & aircon27 EL electrical system
Nissan and Datsun Nissan 180SX S13 1989 Workshop Manual19 · AT automatic transmission
19 · Transmission

TROUBLE DIAGNOSES - Nissan 180SX S13 Workshop Manual

Make
Nissan and Datsun
Model
180SX Nissan 180SX S13 1989 Workshop Manual
Section
General › TROUBLE DIAGNOSES - Nissan 180SX S13 Workshop Manual
AT automatic transmissionTROUBLE DIAGNOSES - Nissan 180SX S13 Workshop Manual

TROUBLE DIAGNOSES

TROUBLE DIAGNOSES

Self-diagnosis (Cont'd)

REVOLUTION SENSOR CIRCUIT CHECK

N.G. | Repair or replace revolution | 4

CHECK REVOLUTION

Revolution sensor SENSOR. — Refer to ‘Electrical sensor. 4 4 Components Inspection”. yor:

|

N.G. | Check the following items.

CHECK INPUT SIGNAL,

1618 @ Harness continuity between “|

1. - A/T control unit A/T control unit and revo- 7 3 lution sensor (Main harness) = SATI40B

bd Harness continuity between

2. Check voltage between A/T

revolution sensor and E.C,U.

control unit terminal (6 and

(Main harness}

ground while driving.

® Ground circuit for E.C.U. (Measure with A.C. range.) — Refer to section EF & EC. Voltage: At 0 km/h (0 MPH): OV At 30 km/h (19 MPH): 1V or more (Voltage rises gradually in (e 117)

response to vehicie speed)

O.K. | — CONNECT 16 — ; NG 1. Perform A/T control unit Perform self-diagnosis again after €> Ww Air anne driving for a while. - input/output signal inspection.

2. \fN.G., recheck A/T control OK. unit pin terminals for damage v or connection of A/T control

INSPECTION END

unit harness connector. ac,

SATT37B8 7

SPEED SENSOR CIRCUIT CHECK

0) Speed NG. Check the following items. sensor

CHECK INPUT SIGNAL.

‘le

1. (R Py 4 Speed sensor and ground 24 circuit for speed sensor ig

A/T control unit

— Refer to section EL. @ Harness continuity between

2. Check voltage between A/T control unit terminal @4 and A/T control unit and speed At2-3km/h sensor (Main harness) {1-2 MPH) ground while driving at 2 to 3 krn/h (1 to 2 MPH) for 1m (3 ft) or more. Voltage: Varies from OV 4s to 5V I at O.K. connect || Lia *¥ € > vig} A/T control Perform self-diagnosis again after | N-G. | 4. Perform A/T control unit | input/output signal inspection. driving for a while. unit terminal

2. 1ENLG., recheck A/T control O.K. @ @ unit pin terminals for damage ¥ or connection of A/T control

INSPECTION END

unit harness connector. —, SAT7386 AT-36

Parts & tools for this job For Nissan 180SX

As an Amazon Associate we earn from qualifying purchases.