Bravo/Brava (182) Factory Service Manual (1995-2001): 70 Bodywork
Also for this vehicle: Bravo Factory Service Manual (2007-2014).
General
Engine
Transmission
Steering & suspension
Electrical
Body & interior
Choose Sections to see everything in a chapter, or a chapter title to start at its first page.
- Bodywork › Bumper
Bumpers3 pages
Bonnet lid2 pages
Interior fittings4 pages
Window glasses14 pages
Replacing body panels41 pages
- General instructions for the repair
- Graphic index
- Symbols
- Front wing
- Refitting
- Replacing rear wing (7090a 54)*23456789
- Preparation and painting procedure23
- Replacing rear wing (7090a 54)*
- Removing off cuts and preparing edges of bodyshell
- Preparing the spare part and checking that it is correctly positioned on the bodyshell
- Finishing operations
- Replacing underdoor side member (7090g 62)*
- Removing off cuts and preparing edges of bodyshell
- Preparing the spare part and checking that it is correctly positioned on the bodyshell
- Finishing operations
- Replacing vehicle roof panel (7090a 58)*
- Removing off cuts and preparing edges of bodyshell
- Positioning the replacement part
- Finishing operations
- Replacing rear cross member lining (7090g 76)*
- Removing off cuts and preparing edges of bodyshell
- Positioning the replacement part
- Finishing operations
- Replacing rear cross member lining (7090a 46)*
- Removing off cuts and preparing edges of bodyshell
- Positioning the replacement part
- Finishing operations
- Replacing rear light cluster housing (7090g 86)*
- Removing off cuts and preparing edges of bodyshell
- Positioning the replacement part
- Finishing operations
Replacing structural body panels32 pages
- Graphic index
- Symbols
- Replacing front cross member lining (7090g 07)*
- Removing off cuts and preparing edges of bodyshell
- Positioning the front cross member and welding
- Finishing operations
- Replacing complete front side panel (7090g 10)*
- Removing off cuts and preparing edges of bodyshell
- Positioning the replacement internal panel
- Preparing the replacement outer panel
- Welding replacement outer panel
- Finishing operations
- Replacing front pillar (7090g 30)*
- Removing off cuts and preparing edges of bodyshell
- Preparing the replacement parts and check that they are correctly positioned on the bodyshell
- Finishing operations
- Replacing centre pillar (7090g 40)*
- Removing off cuts and preparing edges of bodyshell
- Preparing the replacement parts
- Finishing operations
- Replacing underdoor side member front reinforcement (7090g 30)*
- Removing off cuts and preparing edges of bodyshell
- Paat23mot
- Replacing structural body panels
- Replacing underdoor side member rear reinforcement (7090g 54)*
- Removing off cuts and preparing edges of bodyshell
- Positioning the replacement part
- Finishing operations
- Replacing rear wheel arch (7090g 72)*
- Removing off cuts and preparing edges of bodyshell
- Positioning the replacement part
- Replacing structural body panels
Bodyshell10 pages
- Typical measurements
- Measuring dimensions of centre and rear pillar housing
- Measuring door housing dimensions
- Measuring dimensions of centre pillar housing and door housings (3 door version)
- Measuring door housing dimensions
- Measuring rear tailgate housing dimensions (3 door version)
- Figures for adjusting moveable parts (5 door version)
- Figures for adjusting moveable parts
- Squaring body
- Diagram for checking the underbody
Replacing structural body panels14 pages
- Graphic index
- Partial replacement of front panel
- Removing off cuts and preparing edges of bodyshell
- Paat49mot
- Bodywork
- Welding the outer panel replacement part
- Preliminary procedures and safety regulations
- Removing the off cuts, preparing the edges of the bodyshell
- Preparing the spare part
- Welding the spare part
- Bodywork
- Welding the spare part and finishing off
- Positioning the replacement part
- Finishing operations