Fabia Mk1: Drive unit
Also for this vehicle: Fabia Mk2.
Steering & suspension
Engine
Body & interior
Heating & A/C
Transmission
General
Choose Sections to see everything in a chapter, or a chapter title to start at its first page.
1.9/96 TDI Engine, Mechanics97 pages
- Technical Data › Technical data
Engine assy,cylinder block,crankcase › Removing and installing engine5 pages
Enginecrankshaft group, pistons20 pages
Removing and installing V-ribbed belt5 pages
Removing and installing, tightening the toothed belt6 pages
- Summary of components
Removing and installing, tightening the toothed belt4 pages
Removing and installing sealing flange and flywheel4 pages
Crankshaft, Piston and Conrod5 pages
Engine cylinder head, valve gear16 pages
Removing and installing cylinder head7 pages
- Repairing Valve Gear
Valve Seats/Valves Guide/Valve Stem Seal5 pages
Engine lubrication4 pages
Removing and installing parts of the lubrication system2 pages
- Removing and installing oil pan
- Testing oil pressure and oil pressure switch
Engine cooling12 pages
Parts of cooling system - Summary of components8 pages
- Parts of the cooling system fitted to body
- Parts of cooling system engine side
- Connection diagram for coolant hoses
- Draining and filling up coolant
Checking the coolant system for leaktightness3 pages
Removing and installing radiator, coolant pump, coolant regulator4 pages
Fuel supply, gas operation18 pages
Removing and installing parts of the fuel supply - Part 110 pages
Removing and installing parts of the fuel supply - Part 26 pages
Exhaust turbocharger, G-charger14 pages
Charge-air system with exhaust gas turbocharger - Part 110 pages
- Regulations concerning cleanliness when working on the exhaust gas turbocharger
- General instructions for charge air system
- Removing and installing exhaust turbocharger with component parts
- Removing and installing parts of the charge air cooling
- Removing and installing charge air cooler
- Connection diagram for vacuum hoses
Charge-air system with exhaust gas turbocharger - Part 24 pages
Exhaust system7 pages
Removing and installing parts of the exhaust system4 pages
Exhaust gas recirculation system3 pages
1.0/37; 1.4/44; 1.4/50 Drive Unit, Fuel injection97 pages
Self diagnosis, V.A.G Inspection Service22 pages
Self-diagnosis I10 pages
Mixture preparation system, electronic inj.,Gas63 pages
Fuel Injection System10 pages
- Safety measures
- Rules of cleanliness
- General notes on the injection system
- Overview of fitting locations
- Removing and installing parts of the injection system
- Disassembling and assembling fuel distributor with injectors
- Disassembling and assembling intake manifold
- Disassembling and assembling the air filter
- Removing and installing air filter
Lambda control5 pages
- Check lambda probe and lambda control (engines with identification characters ARV, AME, AZE)
- Check lambda probe and lambda control upstream of catalytic converter (engines with identification characters AQV, ATZ, AQW, AZF
- Check lambda probe and lambda control downstream of catalytic converter (engines with identification characters AQV, ATZ, AQW, A
- Inspecting catalyst efficiency (engines with identification characters AQV, ATZ, AQW, AZF)
Tank ventilation8 pages
Testing Activated charcoal filter system solenoid valve 1 N807 pages
Electronic power control12 pages
Function of the electronic engine power output regulation (E-gas)2 pages
- Functional check of fault lamp for the EPC
Inspecting Throttle valve control unit J3384 pages
Check accelerator pedal position sender4 pages
Ignition system, glow plug system12 pages
1.4/55; 1.4/59; 1.4/74 engine - fuel injection112 pages
Self diagnosis, V.A.G Inspection Service24 pages
Self-diagnosis I10 pages
- Properties of the self-diagnosis
- Technical data of self-diagnosis
- Meaning of the exhaust gas warning light K83
- Connecting up the vehicle system tester V.A.G 1552 and selecting the control unit for engine electronics
- Interrogating and erasing fault memory of engine control unit
- Automatic test sequence
Performing actuator diagnosis3 pages
Mixture preparation system, electronic inj.,Gas73 pages
Repairing the injection system12 pages
- Safety measures
- Rules of cleanliness
- General notes on the injection system
- Installed location overview for engines with the engine identification characters AUA, AUB
- Installed location overview for engines with engine identification characters BBY, BBZ, BKY
- Fitting locations for engine with identification characters BUS - Overview
- Disassembling and assembling intake manifold
- Disassembling and assembling fuel distributor with injectors
Testing components and functions27 pages
- Testing Intake manifold pressure sender G71
- Testing Intake manifold temperature sender G42/G72
- Check sender for coolant temperature G62
Inspecting Activated charcoal filter system solenoid valve 1 N808 pages
- Inspecting function of the activated charcoal filter system solenoid valve 1 N80
- Testing the operation of the activated charcoal filter system
- Checking the consistency of the activated charcoal filter
- Check solenoid valve for tightness
- Testing the resistance of the solenoid valve
- Test control
- Checking voltage supply
Testing Exhaust gas recirculation valve N184 pages
Testing the intake system for tightness (unmetered air)2 pages
- Testing intake manifold preheating
- Idle testing
- Testing the engine operating conditions
Electronic power control12 pages
Function of the electronic engine power output regulation2 pages
- Inspecting fault lamp for the EPC
Testing throttle valve control unit J3384 pages
Testing Accelerator pedal position sender4 pages
Engine control unit8 pages
- Wiring and Component Test with Test Box V.A.G. 1598/31 or V.A.G 1598/22
- Testing voltage supply for engine control unit
- Procedure after voltage supply has been interrupted
- Replacing engine control unit
- Coding engine control unit
- Adjusting the engine control unit to the throttle valve control unit
- Clean throttle valve control unit J338
Testing auxiliary signals9 pages
Ignition system, glow plug system › Repairing ignition system15 pages
- General notes on the ignition system
- Removing and installing parts of the ignition system for engines with engine identification characters AUA, AUB
- Removing and installing parts of the ignition system for engines with engine identification characters BBZ, BBY, BKY, BUD
- Safety measures
- Testing hall sender G40
- Check engine speed sender G28 , remove and install
Checking the ignition transformer (for engines with engine identification characters AUA, AUB)4 pages
- Check ignition coils with power output stage (engines with engine identification characters BBY, BKY, BBZ, BUD)
- Removing and installing ignition coils with power output stages
- Testing knock sensor G61
- Test combustion misfiring
1.0/37; 1.4/44; 1.4/50 kW MPI engine95 pages
- Technical Data › Technical data
Self diagnosis, V.A.G Inspection Service › Self diagnosis, safety measures, cleanliness regulations, directions8 pages
- Self-diagnosis
- Safety precautions when working on the fuel supply system
- Rules of cleanliness to observe when working on the fuel supply system
- Safety measures to apply when working on the fuel injection and ignition system
- General notes on the injection system
- General notes on the ignition system
- Additional instructions when undertaking assembly work on the air-conditioning system
Engine assy,cylinder block,crankcase › Removing and installing engine4 pages
Enginecrankshaft group, pistons13 pages
Removing and installing V-ribbed belt5 pages
Disassembling and Assembling Cylinder Block and Crankshaft7 pages
- Disassembling and assembling piston, conrod and liner
Engine cylinder head, valve gear16 pages
Removing and installing cylinder head5 pages
Engine lubrication › Removing and installing parts of the lubrication system5 pages
Engine cooling › Parts of cooling system - Summary of components10 pages
Fuel supply, gas operation18 pages
Removing and installing parts of the fuel supply system6 pages
Testing parts of fuel supply system7 pages
Inspecting the operating and holding pressure of the fuel3 pages
Electronic Engine Power Control (Electronic throttle)2 pages
Activated charcoal filter3 pages
Mixture preparation system, electronic inj.,Gas13 pages
Fuel Injection System11 pages
- Overview of fitting locations
- Removing and installing parts of the injection system
- Summary of components of fuel rail with injection valves
- Summary of components of intake manifold
- Summary of components of air filter
- Removing and installing air filter
Checking the tightness of the injection valves and the fuel injection rate3 pages
- Clean throttle valve control unit J338
Exhaust system › Removing and installing parts of the exhaust system5 pages
Ignition system, glow plug system › Ignition system2 pages