Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

DESCRIPTION — Refrigeration System - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › DESCRIPTION — Refrigeration System - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXDESCRIPTION — Refrigeration System - Nissan 240SX 1991-1992 Workshop Manual

DESCRIPTION — Refrigeration System

DESCRIPTION — Refrigeration System

V-5 Variable Displacement Compressor (Cont'd)

Operation When the air conditioner is OFF, the E.C.C.S. detects the load applied to the engine, and controls the A.A.C. valve to adjust the engine idling speed to the appropriate rpm by supplying additional air from the A.A.C. valve. When the air conditioner is ON (A/C relay is ON), and when the ambient temperature switch is ON (this switch turns ON automatically when the ambient temperature rises to approx. 25°C (77°F) or higher), the F.1.C.D. solenoid valve is energized and additional air is supplied to the engine. If the appropriate engine speed is not reached, the A.A.C. valve supplies the additional air required to increase the engine rpm. If the ambient temperature switch is OFF (this switch turns OFF when the ambient temperature is below 22°C (72°F) even when the air conditioner is ON (A/C relay is ON), the F.1.C.D. solenoid is deenergized, and the idling speed is controlled so that the appropriate rpm can be achieved by operation of the A.A.C. valve only. IGNITION gwen | ACC or ON

FUSE . : 10A tempersture °C Cr) Ambient F.LC.D. Below 19-22 (66 - 72) OFF OFF Above 22 : | A/C (72-77) - 25 ON ON RELAY Idle seed: (rpm) E

AIC OFF | A/CON

z M/T > 3 70050 1,000+50 [a x A/T] in 'N” position 3 w z 545 | 8 zas 3 (e) uw a 2i zr S 2%

> = RHA542C ONES Acceleration

Cut Syst

ration em RUNNING This system is controlled by the E.C.C.S. control unit. When the engine is heavily over loaded (throttle sensor judges that throttle valve is at full throttle position), the compressor is

[/ ruse

turned off for approx. 4 seconds to reduce overloading.

Additionally when the temperature of engine coolant rises |

above approx. 113°C (235°F), the compressor is turned off.

| A/C RELAY

g 4 THROTTLE SENSOR | az S —_) 1 3 v3 o To thermo control « Oo - OO amp. and Ww O | ENGINE A/C switch rs} TEMPERATURE . D SENSOR [lee a a S oO Oo Le — = = RHA543C HA-17

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.