Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

TROUBLE DIAGNOSES

TROUBLE DIAGNOSES

Diagnostic Procedure 26 (Cont'd)

CAR SPEED SEN CIRCUN

INSPECTION START

AFTER TOUCH START,

DRIVE VEHICLE

Vv AT 10 km/h (6 mph) OR (MORE WITHIN 15 sec.

CHECK SPEEDOMETER FUNCTION.

G > Check vehicle speed sen N.G. - Make sure that speedometer functions sor and circuit. properly. (Refer to EL section.) O.K. [next

][__ START

_] v seFe31.| | CHECK INPUT SIGNAL CIRCUIT. N.G. | Check the following. o\ Perform ‘CAR SPEED SEN e Harness connectors(!), q

CIRCUIT” in “FUNCTION TEST”

(153)

wr MONITOR = NO FAIL CL)

mode with CONSULT.

e Harness connectors

CAR SPEED SEN

—-'10mph OR (tue) , 2) —\ 1) Read vehicle speed sensor e Harness continuity signal in “DATA MONITOR” between E.C.U. and mode with CONSULT. combination meter CONSULT value should be the If N.G., repair harness or same as the speedometer indi- connectors. cation. | RECORD OR SEF995K 1) Turn ignition switch ‘OFF’. 2) Disconnect E.C.U. harness con- nector and combination meter harness connector. ay msconnecr ag "scownecr 3) Check rene continuity €&) €) between | .C.U. terminal @ = and terminal @ (Models with- |[_C7unit

[ol CONNECTOR ]|

J

out head-up display), ® (Mod-

els with head-up display).

le ble olde

32

| UFlothi iii Continuity should exist. O.K. Vv [S (ies)

Check E.C.U. pin terminals for damage

. 4 / or the connection of E.C.U. harness connector. €& Perform FINAL CHECK by the following procedure after repair is completed. Ik] 1 [m[n[o]p]

FINAL CHECK

[a[r]sitlulv]

Vv MEF690A Start engine. : Perform self-diagnosis (Mode II). N.G. | Recheck E.C.U. pin termi- nals for damage or the connection of E.C.U. har- ness connector.

v

INSPECTION END

EF & EC-106

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.