Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

TROUBLE DIAGNOSES

TROUBLE DIAGNOSES

Diagnostic Procedure 43 (Cont’d)

Condenser fan /

INSPECTION START

Ww O.K.

CHECK CONDENSER FAN OP-

INSPECTION END

ERATION. 1) Start engine. 2) Set temperature lever at full cold position. 3) Turn air conditioner switch

MEF801A 4) Turn blower fan switch ‘‘ON”’. 5) Run engine at idle for a few minutes with air conditioner operating. 6) Make sure that condenser fan operates. 3) ‘ N.G. N.G.

CHECK POWER SUPPLY.

Check the following. Vv 1) Turn air conditioner switch e Harness connectors (11) , “OFF”’. e ‘“GY”’ fusible link 2) Turn blower fan switch e ‘G” fusible link SEC498B “OFF”’. e 10A fuse 3) Stop engine. e Harness continuity between 4) Disconnect condenser fan re- battery and condenser fan re- lay. lay 5) Turn ignition switch ‘‘ON”’. e Harness continuity between 6) Check voltage between termi- fuse and condenser fan relay nals (2), @ and ground. If N.G., repair harness or con- Voltage: Battery voltage nectors. yo N.G.

CHECK GROUND CIRCUIT.

Repair harness or connectors. Vv 1) Turn ignition switch ““OFF’’. SEF216L 2) Disconnect condenser fan mo- 40 AE tor harness connector. 3) Check harness continuity be- tween terminal @ and termi-

(Mr fel comecTor ||

nal (), terminal @ and body 9 ground. Continuity should exist. O.K. fp) Vv CUIT. « J

N.G. rg Check the following. Vv e Harness connectors F8, MEF722A| | 1) Disconnect E.C.U. harness e Harness continuity between connector. E.C.U. and condenser fan re- 2) Check harness continuity be- lay

CHECK OUTPUT SIGNAL CIR-

ACTIVE TEST

tween E.C.U. terminal

@ and If N.G., repair harness or con-

terminal @.

RADIATOR FAN OFF

nectors. Continuity should exist.

==== MONITOR ====

jox

ENG TEMP SEN

80°C ®

[ON | | SEF999K

EF & EC-167

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.