Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

WIRELESS EQUIPMENT - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › WIRELESS EQUIPMENT - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXWIRELESS EQUIPMENT - Nissan 240SX 1991-1992 Workshop Manual

WIRELESS EQUIPMENT

PRECAUTIONS

WIRELESS EQUIPMENT

E.C.U. When installing a C.B. ham @ Do not disassemble E.C.C.S. Do not apply undue force to radio or a mobile phone, be control unit. (E.C.U.) mounting bracket. sure to observe the following, Before connecting or discon- @ Do not turn diagnosis mode as installation location may af- selector forcibly. necting E.C.U. connector, make fect the electronic control sys- sure red and green LEDs are @ If a battery terminal is discon- tems. nected, the memory will return off after turning ignition key off. Keep antenna as far as possi- 1) to the ROM value. The E.C.C.S. Always install the properly ble away from electronic con- will now start to self-control at specified E.C.U. on car; other- trol units. wise, erroneous engine opera- its initial value. Engine opera- Keep antenna feeder line more 2) tion may result. tion can vary slightly when the than 20 cm (7.9 in) away from Disconnect connector by pull- terminal is disconnected. How- harness of electronic controls. ing it (not the harness) straight ever, this is not an indication Do not let them run parallel for out. of a problem. Do not replace a long distance. Before connecting connector, parts because of a slight varia- Adjust antenna and feeder line make sure all pins are straight. 3) tion. so that standing-wave ratio can be kept smaller. Be sure to ground radio to ve- 4) hicle body. BATTERY INJECTOR Always use a 12 volt battery as @ Do not disconnect injector har- @ a power source. ness connectors with engine @ Do not disconnect battery running. cables while the engine is run- Do not apply battery power di- @ ning. rectly to injectors; otherwise Do not reverse polarity of bat- @ injectors will be damaged. tery when connecting it. Other- wise, E.C.U. and/or injectors may be burned.

FUEL PUMP

Do not operate fuel pump when there is no fuel in lines. Do not reuse fuel hose clamps. Tighten fuel hose clamps to the specified torque.

E.C.C.S. HARNESS HANDLING

Securely connect E.C.C.S. har- JW ness connectors.

E.C.C.S. PARTS HANDLING

A poor connection can cause Handle air flow meter carefully @ extremely high voltage to de- to avoid damage.

velop in the coil and condenser, Do not disassemble air flow @ Do not depress accelerator resulting in damage to ICs. @ meter. Keep E.C.C.S. harness at least pedal when starting. Do not clean air flow meter @

WHEN STARTING

Immediately after starting, do

10 cm (3.9 in) away from adja- e@ with detergent.

not rev up engine unnecessari-

cent harnesses, to prevent an Do not jolt or jar the crank @ E.C.C.S. system malfunction ly. angle sensor.

Do not rev up engine just prior

due to receiving external noise, @ degraded operation of ICs, etc. to shutdown. Keep E.C.C.S. parts and har- nesses dry. Before removing parts, turn off ignition switch and then dis- connect battery ground cable.

SEF961K

EF & EC-3

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.