Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

Inner shim - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › Inner shim - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXInner shim - Nissan 240SX 1991-1992 Workshop Manual

Inner shim

REAR DISC BRAKE (CL9H) — Caliper

Copper washer 634 ao) 17 -20(1.7 - 2.0, 12 - 14) Air bleeder ‘Brake hose sa (©) 7 -9 (0.7 -0.9, 5.1 -6.5) aa) Pin bolt > (0) 22 - 31 (2.2 -3.2, Ps) & 16 - 23) > Cam BEGa (R) a4 Cam bolt Cylinder body Lever (0) : N-m (kg-m, ft-lb) Return spring i\ (9) 22 - 31 (2.2 - 3.2, | | eo washer P. : P.B.C. (Poly Buty! Cuprysil) & U7 25 - 29 (2.5 - 3.0, 16 - 23) l grease or silicon-based 18 - 22) grease point R : Rubber grease point 4 A Z Torque member Cable stay AN Rod EE ® B : Brake fluid point a—-O 26 - 36 (2.7 -3.7, 20 - 27) fixing bolt \ Loving =e K Push rod BEEB®) TM. (C) 38 - 52 (3.9 - 5.3, 28 - 38) ®

Inner shim

LO KR Piston seal %<)

a Key plate

rae 4 Ci Ring C ° Sy RingA Seat oe Spacer Spring Pin ER) @ Spring cover a “A Wave washer Pad retainer =o (R) S Ring B ¢ _ — 4 Spacer i . — ; a Ball bearing a mS\ Adjusting nut Outer pad q : Cur (Ea ® a y N. Outer shim Piston fF} ®) N Pad Torque member retainer aA) Piston boot 'S<) Ea) SBR481A

Pad Replacement

CAUTION: When cylinder body is swung up, do not depress brake pedal because piston will pop out. Release parking brake. @ Remove parking cable stay fixing bolt, pin bolts and lock spring. @ Then remove pad retainers, pads and shims.

@ When installing pads, retract piston into cylinder body by turning it clockwise. Be careful not to damage piston boot or get oil on rotor. Always replace shims when replacing pads.

SBR641 BR-18

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.