TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
- Make
- Nissan and Datsun
- Model
- 240SX Nissan 240SX 1991-92 Workshop Manual
- Section
- General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
‹ Prev TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop ManualNext › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
TROUBLE DIAGNOSES
TROUBLE DIAGNOSES
Self-diagnosis — Mode II (Self-diagnosticresults) (Cont'd)
| Code No. | Detected items | Malfunction is detected when ... | Check item (remedy) |
|---|---|---|---|
| 11* | Crank angle sensor cir- | |e Either 1° or 90° signal is not entered for the first | |e Harness and connector (lf |
| cuit | few seconds during engine cranking. | harness and connector are | |
| e Either 1° or 90° signal is not input often enough | normal, replace crank angle | ||
| while the engine speed is higher than the speci- | sensor.) | ||
| fied rpm. | |||
| 12 | Air flow meter circuit | e The air flow meter circuit is open or shorted. (An | |@ Harness and connector (If |
| abnormally high or low voltage is entered.) | harness and connector are | ||
| normal, replace air flow | |||
| meter.) | |||
| 13 | Engine temperature | @ The engine temperature sensor circuit is open or | |e Harness and connector |
| sensor circuit | shorted. | e Engine temperature sensor | |
| (An abnormally high or low output voltage is en- | |||
| tered.) | |||
| 14 | Vehicle speed sensor | e The vehicle speed sensor circuit is open or | e@ Harness and connector |
| circuit | shorted. | e Vehicle speed sensor (reed | |
| switch) | |||
| 21* | Ignition signal circuit | e The ignition signal in the primary circuit is not | e Harness and connector |
| entered during engine cranking or running. | e Power transistor unit | ||
| 31 | E.C.U. | e E.C.U. calculation function is malfunctioning. | (Replace E.C.C.S. control unit.) |
| 32 | E.G.R. function | e E.G.R. control valve does not operate. | e E.G.R. control valve |
| (E.G.R. control valve spring does not lift.) | e E.G.R. and canister control | ||
| solenoid valve | |||
| 33 | Exhaust gas sensor cir- | |@ The exhaust gas sensor circuit is open or | e@ Harness and connector |
| cuit | shorted. | e Exhaust gas sensor | |
| (An abnormally high or low output voltage is en- | |@ Fuel pressure | ||
| tered.) | e Injectors | ||
| e Intake air leaks | |||
| 34 | Detonation sensor cir- | e The detonation circuit is open or shorted. | e Harness and connector |
| cuit | (An abnormally high or low voltage is entered.) | e Detonation sensor | |
| 35 | Exhaust gas tempera- | e The exhaust gas temperature sensor circuit is | e@ Harness and connector |
| ture sensor circuit | open or shorted. | e Exhaust gas temperature | |
| (An abnormally high or low voltage is entered.) | sensor | ||
| 43 | Throttle sensor circuit | e The throttle sensor circuit is open or shorted. | e Harness and connector |
| (An abnormally high or low voltage is entered.) | e Throttle sensor | ||
| 45 | Injector leak | e@ Fuel leaks from injector. | e Injector |
| 54 | Signal circuit from A/T | |e The A/T communication line is open or shorted. | e Harness and connector |
| control unit to E.C.U. | |||
| (A/T only) |
*: Check items causing a malfunction of crank angle sensor circuit first, if both ‘““CRANK ANGLE SENSOR (No. 11)” and “IGN SIGNAL-PRIMARY (No. 21)’ are displayed one after the other.
EF & EC-43
‹ Prev TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop ManualNext › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
Parts & tools for this job For Nissan 240SX
- TOOLTorque wrenchSearch: 3/8 inch torque wrench
- TOOLSocket setSearch: socket set metric
- BOOKHaynes manualSearch: Haynes manual Nissan 240SX
As an Amazon Associate we earn from qualifying purchases.