Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

TROUBLE DIAGNOSES

TROUBLE DIAGNOSES

Diagnostic Procedure 40 (Cont’d) “A(e \@ Stine Ly

INSPECTION START

‘A CONTROL VALVE.

SLR

CHECK VACUUM SOURCE TO SWIRL | 0-K.

INSPECTION END

y

1) Start engine and warm it up suffi- ciently.

\\Vacuum hose ee

3) After a few seconds, disconnect vac-

2) Stop engine to swirl control valve MEF712A uum hose to swirl control valve and restart engine. B}

4) Make sure that vacuum exists under

@SWRL CONT S/V CIRCUIT

the followin diti g conditions. DOES Engine speed is less than 2,400 rpm: THE Rone Vacuum should exist. OMe

Engine speed is more than 2,400

EVERY 3 SECONDS?

rpm: Vacuum should not exist. N.G. [next ||

NO || YES

| B ¥ SEF637L| | CHECK CONTROL FUNCTION.

O.K. > CHECK VACUUM HOSE

1) Turn ignition switch “ON”.

AND SWIRL CONTROL

1B _ connect

2) Perform “‘SWRL CONT S/V

VALVE. C/UNIT |o! CONNECTOR CIRCUIT” in ‘FUNCTION 1) Check vacuum hose 25 TEST” mode with CONSULT. and swirl control valve OR for clogging, cracks 1) Check voltage between E.C.U. and proper connection. es terminal @) and ground. —— Voltage:

(Gy ‘a oly il

2,400 rpm: AP, Engine speed is less than Approximately 0V MEF713A Engine speed is more than 2,400 rpm: = / Battery voltage @) ——_— : N.G. Split D) ‘

CHECK POWER SUPPLY.

N.G. »| Check the following. Clogging 1) Stop engine. @ Harness connectors(), 2) Disconnect S.C.V. control solenoid _ valve harness connector. e 10A fuse AN 3) Turn ignition switch ‘‘ON’”’. e@ Harness continuity __ lmproper connection 4) Check voltage between terminal ® between fuse and SEF816F and ground. S.C.V. control solenoid Voltage: Battery voltage valve [) = € OK.

If N.G., repair harness or

® “» connectors.

Bs

~ MEF714A EF & EC-142

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.