Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

TROUBLE DIAGNOSES

TROUBLE DIAGNOSES

Diagnostic Procedure 29 (Cont’d)

California model

INSPECTION START

Vv O.K.

CHECK VACUUM SOURCE TO E.G.R.

CHECK COMPONENTS

Vv

CONTROL VALVE.

(E.G.R. control valve, Vacuum hose connected 1) Start engine and warm it up suffi- B.P.T. valve and exhaust to E.G.R. control valve MEF694A ciently. gas temperature sensor). 2) Perform self-diagnosis. Refer to ‘Electrical Com- LB) — CONNECT Make sure that none of the codes ponents Inspection’.

(L_cvunt [ef CONNECTOR ]]

No. 12, No. 13, No. 35 or No. 43 are (See page EF & EC-165, 105 displayed. 166.) 3) Keep engine speed at about 2,000 N.G. (ey rpm. 4) Disconnect vacuum hose to E.G.R. control valve. A ty 4 clNy 5) Make sure that vacuum exists under the following conditions. Vv At idle: Replace malfunctioning MEF695A Vacuum should not exist. componeni(s). Engine speed is about 2,000 rpm.: Vacuum should exist. N.G. 8) ’ O.K.

| CHECK VACUUM HOSE.

CHECK CONTROL FUNCTION.

1) Check voltage between E.C.U. termi- 1) Check vacuum hose naldoand ground under the follow- for clogging, cracks ing conditions. and proper connection. —a

Improper connection

Voltage: At idle SEF816F Approximately 0V Engine speed is about 2,000 DISCONNECT rpm. Battery voltage N.G. [D) Vv N.G. Check the following.

CHECK POWER SUPPLY.

e Harness connectors(9), 1) Stop engine. 2) Disconnect E.G.R. & canister control solenoid valve harness connector. e 10A fuse 3) Turn ignition switch ‘‘ON”’. e Harness continuity MEF696A 4) Check voltage between terminal ® between E.G.R. & can- and ground. ister control solenoid DISCONNECT DISCONNECT Voltage: Battery voltage valve and fuse HS TS lf N.G., repair harness or O.K. connectors.

(L_c/unrt__[o[ CONNECTOR |

105 ® (oF . J MEF697A

EF & EC-111

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.