Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

TROUBLE DIAGNOSES

TROUBLE DIAGNOSES

Consult (Cont’d)

SELF-DIAGNOSTIC RESULTS MODE

DIAGNOSTIC ITEMDIAGNOSTIC ITEM IS DETECTED WHEN ...CHECK ITEM (REMEDY)
CRANK ANGLE SENSOR*Either 1° or 120° signal is not entered for the first fewe@ Harness and connector
seconds during engine cranking.(If harness and connector are
Either 1° or 120° signal is not input often enoughnormal, replace crank angle
while the engine speed is higher than the specifiedsensor.)
rpm.
AIR FLOW METERThe air flow meter circuit is open or shorted.e Harness and connector —
(An abnormally high or low voltage is entered.)(If harness and connector are
normal, replace air flow
meter.)
ENGINE TEMP SENSORThe engine temperature sensor circuit is open ore Harness and connector
shorted.e Engine temperature sensor
(An abnormally high or low output voltage is en-
tered.)
CAR SPEED SENSORThe vehicle speed sensor circuit is open or shorted.e Harness and connector
e Vehicle speed sensor (reed
switch)
IGN SIGNAL-PRIMARY*The ignition signal in primary circuit is not enterede Harness and connector
during engine cranking or running.e Power transistor unit
CONTROL UNITE.C.U. calculation function is malfunctioning.(Replace E.C.C.S. control unit.)
EGR SYSTEM**E.G.R. control valve does not operate.e E.G.R. control valve
(E.G.R. control valve spring does not lift.)e E.G.R. and canister control
solenoid valve
EXH GAS SENSORThe exhaust gas sensor circuit is open or shorted.Harness and connector
(An abnormally high or low output voltage is en-Exhaust gas sensor
tered.)Fuel pressure
Injectors
Intake air leaks
DETONATION SENSORThe detonation circuit is open or shorted.e Harness and connector
(An abnormally high or low voltage is entered.)e Detonation sensor
EXH GAS TEMP SENSOR**The exhaust gas temperature sensor circuit is opene Harness and connector
or shorted.e Exhaust gas temperature
(An abnormally high or low voltage is entered.)sensor
THROTTLE SENSORThe throttle sensor circuit is open or shorted.e Harness and connector
(An abnormally high or low voltage is entered.)e Throttle sensor
INJECTOR LEAK**Fuel leaks from injector.e Injector

*: Check items causing a-malfunction of crank angle sensor circuit first, if both “CRANK ANGLE SENSOR” and “IGN SIGNAL-PRIMARY” come out at the same time. **:The diagnostic item marked ‘‘**’’ is applicable to vehicles for California only.

EF & EC-48

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.