Workshop Manuals Factory service & repair Nissan and Datsun
01 QUICK REFERENCE INDEX02 Front Cover03 Foreword04 Table of Contents05 General Information06 Windshield Header Trim07 Windshield Header Molding08 Weatherstrips and Retainers09 Rear Seat10 Quarter Trim Panel11 Quarter Window and Regulator12 Door and Door Window13 Seat Belts14 Back and Quarter Belt Moldings15 Headliner Assembly16 Top Cover Assembly17 Backlite Assembly18 Stay Pads, Side and Rear19 No. 1 Bow20 No. 2 Bow21 No. 3 Bow22 No. 4 Bow23 Rear and Side Rail24 Hydraulic System25 Electrical26 Deck Lid Hinge and Trunk Trim27 Body Structural28 Index29 Back Cover30 QUICK REFERENCE CHART
Nissan and Datsun Nissan 240SX 1991-92 Workshop Manual01 · QUICK REFERENCE INDEX
01 · General

TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

Make
Nissan and Datsun
Model
240SX Nissan 240SX 1991-92 Workshop Manual
Section
General › TROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual
QUICK REFERENCE INDEXTROUBLE DIAGNOSES - Nissan 240SX 1991-1992 Workshop Manual

TROUBLE DIAGNOSES

TROUBLE DIAGNOSES

Diagnostic Procedure 44 (Cont'd)

INSPECTION START

BM PW/ST SIGNAL CIRCUIT

v

HOLD STEERING WHEEL

O.K.

INSPECTION END

CHECK OVERALL FUNCTION.

IN A FULL

1) Turn ignition switch ‘ON’.

LOCKED position

2) Perform ‘‘PW/ST SIGNAL THEN CIRCUIT” in “FUNCTION

TOUCH START

TEST” mode with CONSULT. OR |

|[_ START

[next 1) Start engine. 2) Check power steering oil pres- SEF200L sure switch signal in “DATA MONITOR” mode with CON- i)

*% MONITOR

*¥NO FAIL

SULT. Steering is neutral: OFF

PW/ST SIGNAL

OFF Steering is turned: ON OR ® 1) Start engine. 2) Check voltage between E.C.U. terminal @ and ground with I RECORD 1 CONSULT or tester. Voltage: SEF5911 When steering wheel is turned quickly. _ ag CONNECT Approximately 0V

[eran icomecrn] [A €

Except above (J Approximately 7-9V N.G. 3) ¥ 28 Ac,

Repair harness or con-

Dare N.G.

CHECK GROUND CIRCUIT.

Vv 1) Stop engine. nectors. 2) Disconnect power steering oil pres-

7 SEF216K

sure switch harness connector. 3) Check harness continuity between terminal ® and engine ground. BI PFs DISCONNECT Continuity should exist. TS yo* N.G.

CHECK INPUT SIGNAL CIRCUIT.

Repair harness or con- Vv 1) Disconnect E.C.U. harness connec- nectors. tor. (® 2) Check harness continuity between E.C.U. terminal @ and terminal @. Continuity should exist.

7 MEF723A

O.K. v N.G. Replace power steering

CHECK COMPONENT

7 DISCONNECT eg Disconnect Vv €) Ae oil pressure switch. (Power steering oil pressure switch). Refer to “‘Electrical Components (C_c7unrt

talb) Inspection’. 43 (See page EF & EC-169.) | yok Check E.C.U. pin terminals for damage ® or the connection of E.C.U. harness e e _/+ connector. MEF724A

[ol CONNECTOR |

EF & EC-153

Parts & tools for this job For Nissan 240SX

As an Amazon Associate we earn from qualifying purchases.